12240-98600 Suzuki Crankshaft, Under


12240-98600 Crankshaft, Under Suzuki DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH Crankshaft
12240-98600 Crankshaft, Under Suzuki
Rating:
8

Buy Crankshaft, Under 12240-98600 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 11-1
 

Compatible models:

Suzuki entire parts catalog list:

DT4LF 1985
DT4LG 1986
DT4LH 1987
DT4SF 1985
DT4SG 1986
DT4SH 1987

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) T400011 Crankshaft Turning Tool 1
A(2) 27610291 Housing 1
27610289 Engine Turning Tool 1
B - E12 Torx Socket 1
C 21825607 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g06362599
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod.Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin.Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g06360869
Install connecting rod cap (2) to connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Use Tooling (B) tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) and Tooling (C) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings.Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
If the glow plugs were removed, install the glow plugs. Ref to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.


Parts crankshaft Suzuki:

12200-98601
 
12200-98601 Crankshaft Assembly
DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH
12200-98602
 
12200-98602 Crankshaft Assembly
DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH
12200-98603
 
12200-98603 Crankshaft Assembly
DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH
12221-98600
 
12221-98600 Crankshaft, Upper
DT4, DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH, DT5Y
12240-98601
 
12240-98601 Crankshaft, Under
DT4LF, DT4LG, DT4LH, DT4SF, DT4SG, DT4SH
Back to top