61231-95570-26H Suzuki Decal, lower cover PORT


61231-95570-26H Decal, lower cover PORT Suzuki DT75TCLG, DT75TCLH, DT75TCLJ, DT75TCLK, DT75TCLL, DT75TCLM, DT75TCLN, DT75TCLP, DT75TCLR, DT75TCLS, DT75TCLT, DT75TCLV, DT85TCLJ, DT85TCLK, DT85TCLL, DT85TCLM, DT85TCLN, DT85TCLP, DT85TCLR, DT85TCLS, DT85TCLT, DT85TCLV, DT85TCLW, DT85TCLX, DT85TCLY Decal
61231-95570-26H Decal, lower cover PORT Suzuki
Rating:
53

Buy Decal, lower cover PORT 61231-95570-26H Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 37-2
 

Suzuki entire parts catalog list:

DT75TCLG 1986
DT75TCLH 1987
DT75TCLJ 1988
DT75TCLK 1989
DT75TCLL 1990
DT75TCLM 1991
DT75TCLN 1992
DT75TCLP 1993
DT75TCLR 1994
DT75TCLS 1995
DT75TCLT 1996
DT75TCLV 1997
DT85TCLJ 1988
DT85TCLK 1989
DT85TCLL 1990
DT85TCLM 1991
DT85TCLN 1992
DT85TCLP 1993
DT85TCLR 1994
DT85TCLS 1995
DT85TCLT 1996
DT85TCLV 1997
DT85TCLW 1998
DT85TCLX 1999
DT85TCLY 2000

Information:

1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) to show the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 4 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 3 upper main bearing.
If the crankcase is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft with tool (D) until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block.5. Put clean engine oil on the lower bearings. Install lower bearings in the bearing caps.6. Install upper bearing in the cylinder block with tool (A). Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly. When the bearing clearance is checked the crankshaft will have to be lifted up against the upper halves of the main bearings with a force equal to the weight of the crankshaft and held to get a measurement with Plastigage. The Plastigage will not hold the weight of the crankshaft. Do not turn the crankshaft when the Plastigage is in position to check bearing clearances. 7. Check the bearing clearance with Plastigage (B) as follows:a) Put the Plastigage in position.b) Put clean engine oil on the threads of the cap bolts. Install the caps and cap bolts, finger tight.c) Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).d) Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb.ft.).e) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120° more. Make sure the main bearing caps are installed with their identification number (7) in alignment with the identification number on the left side of the cylinder block and arrow (6) toward the front of the block.8. Remove the main bearing caps and Plastigage (B).9. The clearance for new bearings must be 0.091 to 0.185 mm (.0036 to .0073 in.). The maximum clearance of used bearings is 0.25 mm (.010 in.).10. Remove upper bearings with tool (A).11. Put clean engine oil on the upper bearings and install with tool (A).12. Install a thrust plate (8) on each side of the No. 3 upper bearing. Install the thrust plates with the side that has the identification "BLOCK SIDE" toward the cylinder block.13. Put clean engine oil on bearings in the caps and install No. 2 through No. 4 main bearing caps. Follow the procedure in Step 7 to tighten the bolts.14. Do Steps 2, 4 through 9 and 11 for the No. 1 and No. 5 main bearings. 15. Check the end play of the crankshaft with tool (C). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.15 to 0.51 mm (0.006 to 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).END BY:a) install oil pump


Parts decal Suzuki:

67282-95610
 
67282-95610 Decal, remote control box PORT
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70T
61443-95640-26G
 
61443-95640-26G Decal, STBD
DT75TCLG, DT75TCLH
61453-95640-26G
 
61453-95640-26G Decal, PORT
DT75TCLG, DT75TCLH
61443-95640-26H
 
61443-95640-26H Decal, STBD
DT75TCLG, DT75TCLH
61453-95640-26H
 
61453-95640-26H Decal, PORT
DT75TCLG, DT75TCLH
61221-95570-26G
61221-95570-26H
Back to top