67701-96300 Suzuki Drag Link Assembly


67701-96300 Drag Link Assembly Suzuki 30ELE, 30ESE, 30MLE, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25MLJ, DT25 Drag
67701-96300 Drag Link Assembly Suzuki
Rating:
58

Buy Drag Link Assembly 67701-96300 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Suzuki entire parts catalog list:

30ELE 1984
30ESE 1984
30MLE 1984
DT20ELG 1986
DT20ELH 1987
DT20ELJ 1988
DT20ESG 1986
DT20ESH 1987
DT20ESJ 1988
DT20MLG 1986
DT20MLH 1987
DT20MLJ 1988
DT20MSG 1986
DT20MSH 1987
DT20MSJ 1988
DT25ELF 1985
DT25ELG 1986
DT25ELH 1987
DT25ELJ 1988
DT25ESG 1986
DT25ESH 1987
DT25ESJ 1988
DT25MLD 1983
DT25MLE 1984
DT25MLF 1985
DT25MLG 1986
DT25MLH 1987
DT25MLJ 1988
DT25MSD 1983
DT25MSE 1984
DT25MSF 1985
DT25MSG 1986
DT25MSH 1987
DT25MSJ 1988
DT25SF 1985
DT30ELD 1983
DT30ESD 1983
DT30LF 1985
DT30MLD 1983
DT30MSD 1983
DT30MSE 1984
DT30SF 1985
DT40ECLE 1984
DT40ECLF 1985
DT40ECSE 1984
DT40ECSF 1985
DT40MCLE 1984
DT40MCLF 1985
DT40MCSE 1984
DT40MCSF 1985
DT50ECLE 1984
DT50MCLE 1984
DT60CLE 1984

Information:


Illustration 1 g06291450
(1) Filter assembly
Illustration 2 g06169208
(2) Drain valve
(3) Connection port
(4) Filter bowl
(5) Filter body
Illustration 3 g06169189
(6) Filter element
Illustration 4 g06169221
(7) Threads (exterior)
(8) Threads (interior)
(9) Air vent screw
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Note:
Ensure that the engine is stopped before any servicing or repair is performed.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
The low-pressure fuel system can be pressurized for a time period after the engine has stopped operating. The operating pressure of the low-pressure fuel system can be 500 kPa (73 psi).
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over any disconnected fuel system components.
Remove the Element
Note: Ensure that the fuel supply valve (if equipped) is in the OFF position. Place a suitable container under the fuel filters to catch any fuel that might spill. Clean up any spilled fuel.
Install a suitable tube onto connection (3). Rotate the drain valve (2) counterclockwise. Two full turns are required.
Open the air vent screw (9) by a couple of turns. Allow the fuel to drain into the container and remove the tube.
Tighten the air vent screw (9), replace sealing ‘O’ ring as necessary.
Remove the filter bowl (4) from filter body (5). Rotate the filter bowl counterclockwise to remove the assembly.
Rotate the filter element (6) counterclockwise and remove the filter element. Clean the filter bowl.Install the Element
Locate the thread (8) in the filter element associated with the threads (7). Spin on the new filter element and tighten the drain valve (2) by hand.
Lubricate the seal on the filter element (6) with clean engine oil. Do NOT fill the filter bowl (4) with fuel before the filter assembly is installed.
Do not use a tool to install the filter assembly. Tighten the assembly by hand. Install the filter bowl (4). Turn the filter bowl clockwise until the filter bowl locks into position against the stops.
The fuel system can be primed, when the filter element has been replaced with a new filter element and the primary filter has been renewed. If necessary, turn the fuel supply valve to the ON.
Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime" topic (Maintenance Section) for more information.


Parts drag Suzuki:

67701-95300
 
67701-95300 Drag Link Assembly
DT50ECLE, DT50MCLE, DT60CLE, DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLG, DT75TCLH, DT85TCLD, DT85TCLE, DT85TCLF
Back to top