55128-87D00 Suzuki DRAIN PLUG

Illustration 1 g00770916
Enter the service mode. Select the "CONFIGURATION" option from the menu by using the keys for direction.
Illustration 2 g00687754
The third line in the above illustration indicates the configuration ID. The settings that correspond to the respective ID numbers are listed in the following table. Each respective ID is classified in either the "display only" or the setting for the ID. In order to change the ID, use the keys for direction and highlight the fourth line. After the ID has been changed, press the "setting" key. When the area that is highlighted moves to the third line, the change has been completed.
Illustration 3 g00687765
In order to clear the setting, highlight the word "STANDBY" in the fourth line and press the "setting" key.
Illustration 4 g00687786
The above illustration shows the screen that confirms the "clear" operation. When "CLEAR?" is being displayed, press the "OK" key. This operation has been completed.Note: See the appropriate service manual for the tool control for the parameters that are not listed.
Table 1
Items For Configuration    
ID     Display Content     Description / Change Method    
1     Model information     Display only (Model name- Model type)    
2     Type of hydraulic oil     Mineral oil: MINERAL
Vegetable oil : BIO OIL    
3     Travel alarm status     Equipped: INSTALLED
Non-equipped: NOT INSTALLED    
4     Water separator Contact type of level switch     NORMALLY OPEN
NORMALLY CLOSE
Non-equipped: NOT INSTALLED    
5     Contact type of NO. 1 fuel filter switch     NORMALLY OPEN
NORMALLY CLOSE
Non-equipped: NOT INSTALLED    
6     Contact type of clogged second fuel filter switch     NORMALLY OPEN
NORMALLY CLOSE
Non-equipped: NOT INSTALLED    
7     Contact type of clogged special filter switch     NORMALLY OPEN
NORMALLY CLOSE
Non-equipped: NOT INSTALLED    
8     Contact type of automatic greasing failure switch     NORMALLY OPEN
NORMALLY CLOSE
Non-equipped: NOT INSTALLED    
9     Overload warning sensor status     Equipped: INSTALLED
Non-equipped: NOT INSTALLED    
10     Pressure of overload warning
Units: kPa (PSI)     Upper limit:
40000 kPa (5801 psi)
Lower Limit:
0 Kpa (0 psi)
1 step:
100 kPa (14 psi)    
301     Switching pressure to low speed of automatic travel speed change
Units: kPa (PSI)     Upper limit:
40000 kPa (5801 psi)
Lower Limit:
0 Kpa (0 psi)
1 step:
100 kPa (14 psi)    
302     Switching pressure to high speed of automatic travel speed change
Units: kPa (PSI)     Upper limit:
40000 kPa (5801 psi)
Lower Limit:
0 Kpa (0 psi)
1 step:
100 kPa (14 psi)    
303     Switching time to low speed of automatic travel speed change
Units: Second     Upper limit: 25.0 sec
Lower limit: 0.0 sec
1 step: 0.1 sec    
304     Switching time to high speed of automatic travel speed change     Upper limit: 25.0 sec
Lower limit: 0.0 sec
1 step: 0.1 sec    
305     Setting speed of one-touch low idle
Units: rpm     Upper limit: Initial speed at Dial position 10
Lower limit: Initial speed at Dial position 1
1 step: 10 rpm    
306     AEC 2nd stage setting speed
Units: rpm     Upper limit: Initial rpm at Dial position 10
Lower limit: Initial rpm at Dial position 1
1 step: 10 rpm    
307     AEC 2nd stage operation time
Units: Second     Upper limit: 25.0 sec
Lower limit: 0.0 sec
1 step: 0.1 sec    
308     Setting change of setting speed for current Dial position
Units: rpm     Upper limit: One step up dial setting less than -50 rpm
Lower limit: One step down setting speed over +50 rpm
Max. value: Initial rpm at Dial position 10
Min. value: Initial rpm at Dial position 1
1 step: 10 rpm    
309     Setting change of torque distribution for the current Dial position
Units: %     0.1% unit display using the decimal point
Upper limit value: 100.0% (200.0% for 321C)
Lower limit value: 0.0%
1 step: 1.0% (0.1% for 321C)
Reset operation is possible    
401     Engine oil recommended change time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
402     Engine oil filter recommended change time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
403     Fuel filter recommended replacement time
Units: Hours     Upper limit: 25500 hour
Lower limit: 0 hour
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
404     Primary filter recommended replacement time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
405     Swing drive oil recommended replacement time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
406     Pilot oil filter recommended replacement time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
407     Drain oil filter recommended replacement time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
408     Hydraulic return filter recommended replacement time
Units: Hours     Upper limit: 25500 hours
Lower limit: 0 hours
1 step: 100 hours (50 hours for 321C)
"0 hour" is used as non-equipped.    
409     Final drive oil change time
Units: Hours     Upper limit: 25500 hours
Lower lim