61435-98101 Suzuki Emblem, Rear


61435-98101 Emblem, Rear Suzuki DT8LT, DT8LX, DT8LZ, DT8ST, DT8SX, DT8SZ Emblem
61435-98101 Emblem, Rear Suzuki
Rating:
43

Buy Emblem, Rear 61435-98101 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 10-2
 

Compatible models:

Suzuki entire parts catalog list:

DT8LT 1980
DT8LX 1981
DT8LZ 1982
DT8ST 1980
DT8SX 1981
DT8SZ 1982

Information:


Table 1
J1939 Code and Description Comments
190-0
Engine Speed : High - most severe (3) The engine rpm has exceeded the trip point that is programmed into the Electronic Control Module (ECM) and the delay time has expired.
The ECM has determined that the detected speed is accurate.
The gas shutoff valve and the ignition are shut off.
The code is logged.
190-15
Engine Speed : High - least severe (1) The engine rpm has exceeded the trip point that is programmed into the ECM and the delay time has expired.
The ECM has determined that the detected speed is accurate.
The code is logged.
190-16
Engine Speed : High - moderate severity (2) The engine rpm has exceeded the trip point that is programmed into the ECM and the delay time has expired.
The ECM has determined that the detected speed is accurate.
The code is logged.
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
Probable Causes
Codes
Governor response
Trip point
Driven equipment
Air chokeRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check for Slow Governor Response
Note: If an engine overspeed occurs during start-up or when the load is reduced, the governor response may be slow.
A. Connect Cat ET.
B. Use Cat ET to monitor the following:
- "Speed Governor Adjustment"
C. Look for the engine response to the worst cases for step-loading and unloading.
Governor Response
Result: The governor response is OK.
Proceed to Test Step 3.
Result: The governor response is NOT OK. The undershoot or the overshoot of the engine speed is excessive.
Repair: Adjust the governor gain. Refer to Systems Operation, "Electronic Control System Parameters".
If the problem is not resolved, proceed to Test Step 3.
3. Check the Trip Point
Note: Do not program the trip point for engine overspeed higher than the maximum ratings of the driven equipment.
A. Verify that the trip point for the engine overspeed is properly programmed.
Trip Point
Result: The trip point is OK.
Proceed to Test Step 4.
Result: The trip point is NOT OK.
Repair: Change the trip point to an acceptable speed.
This parameter requires a factory password in order to change the trip point.
If the problem is not resolved, proceed to Test Step 4.
4. Inspect the Driven Equipment
A. Determine if the driven equipment has additional inputs of energy that could drive the engine beyond the rated rpm.
Driven Equipment
Result: The driven equipment is OK.
Proceed to Test Step 5.
Result: The driven equipment is NOT OK.
Repair: Make corrections to the installation in order to prevent the overspeed from recurring.
If the problem is not resolved, proceed to Test Step 5.
5. Check for Binding of the Air Choke Actuator
A. Remove the electrical power from the engine.
B. Move the actuator rod or the throttle plate while you feel the motion.
Air Choke
Result: The actuator rod or the throttle plate is binding.
Repair: Repair or replace damaged air choke components. Refer to Operation and Maintenance Manual, "Electrohydraulic Actuator - Recondition" for additional information.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts emblem Suzuki:

61422-98101
 
61422-98101 Emblem, Front Suzuki
DT5LT, DT5LX, DT5LZ, DT5ST, DT5SX, DT5SZ, DT8LT, DT8LX, DT8LZ, DT8ST, DT8SX, DT8SZ
61441-98511
 
61441-98511 Emblem, Cover Side Suzuki
DT5LT, DT5LX, DT5LZ, DT5ST, DT5SX, DT5SZ, DT8LT, DT8LX, DT8LZ, DT8ST, DT8SX, DT8SZ
61422-98511
 
61422-98511 Emblem, Front
DT5LZ, DT5SZ, DT8LZ, DT8SZ
61435-98110
Back to top