68111-96J00 Suzuki EMBLEM (S)


68111-96J00 EMBLEM (S) Suzuki DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF300, DF300 EMBLEM
68111-96J00 EMBLEM (S) Suzuki
Rating:
38

Buy EMBLEM (S) 68111-96J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Compatible models:

Suzuki entire parts catalog list:

DF150 2006,2007,2008,2009
DF150 2010
DF150 2011
DF175 2006,2007,2008,2009
DF175 2010
DF175 2011
DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011
DF300 2007,2008,2009
DF300 2010

Information:

The following conditions must exist before any of the preceding codes will become active:
The ECM has been powered for at least 2 seconds.
There are no active 168 codes.
There are no active 3509 (262) codes.Use this procedure to troubleshoot the position sensors for the following valves:
NRS valve
Engine intake throttle valve
Combustion air valve for the Aftertreatment Regeneration Device (ARD)Each position sensor is integral in the associated valve. If the following procedure indicates a fault with the position sensor, then the entire valve must be replaced.The following background information is related to this procedure:The troubleshooting procedures for the diagnostic codes of each position sensor are identical. The 5 VDC sensor supply provides power to all 5 VDC sensors. The ECM supplies 5.0 VDC to terminal "5" of the engine intake throttle valve connector and to terminal "1" of the other valve connectors. The sensor common from the ECM connector goes to terminal "3" of the engine intake throttle valve connector. The sensor common from the ECM connector goes to terminal "2" of the other valve connectors. The sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM. The signal voltage from terminal "4" of the engine intake throttle valve is supplied to the appropriate terminal at the P2 ECM connector. The signal voltage from terminal "3" of the other valves is supplied to the appropriate terminal at the P2 ECM connector.Pull-up VoltageThe ECM continuously outputs a pull-up voltage on the circuit for the sensor signal wire. The ECM uses this pull-up voltage to detect an open in the signal circuit. When the ECM detects a voltage above a threshold on the signal circuit, the ECM generates an open circuit diagnostic code (XXXX-3) for the sensor.If the sensor is disconnected, pull-up voltage at the sensor connector indicates that the wires are not open or shorted to ground. If the sensor is disconnected , the absence of pull-up voltage indicates an open in the signal wire or a short to ground. If the sensor is disconnected and the voltage is different from pull-up voltage, the signal wire is shorted to another wire in the harness.
Illustration 1 g06156781
Schematic diagram for the valve position sensors
Illustration 2 g01981373
Typical view of the pin locations on the P2 connector for the position sensors
(3) Engine intake throttle valve position sensor signal
(15) NRS valve position sensor signal
(16) Combustion air valve position sensor signal
(45) Combustion air valve position sensor 5 VDC supply
(46) Engine intake throttle valve, NRS valve position sensors 5 VDC supply
(55) Combustion air valve position sensor ground
(56) Engine intake throttle valve, NRS valve position sensors ground
Illustration 3 g02186473
Typical view of the pin locations for the valve position sensors on the connectors from the engine to the Clean Emissions Module (CEM)
(1) 5 VDC supply
(2) Combustion air valve position sensor ground
(9) Combustion air valve position sensor signal
Illustration 4 g03177615
Connector for the NRS valve
(1) 5 VDC supply
(2) Position sensor ground
(3) Position sensor signal
Illustration 5 g03177636
Connector for the combustion air valve
(1) 5 VDC supply
(2) Position sensor ground
(3) Position sensor signal


Parts emblem Suzuki:

68165-16B00-13L
EMBLEM, SUZUKI
68165-16B00-13L EMBLEM, SUZUKI
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15A, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF20
68165-98J10
 
68165-98J10 EMBLEM (SUZUKI)
DF250A, DF300, DF300, DF300A
77811-54GC0-0PG
EMBLEM (S) (CHROME)
77811-54GC0-0PG EMBLEM (S) (CHROME)
DF150, DF175, DF250A, DF300A
Back to top