11400-95874 Suzuki GASKET SET (ALL)


11400-95874 GASKET SET (ALL) Suzuki DT50, DT50M, DT50W, DT65, DT65 GASKET
11400-95874 GASKET SET (ALL) Suzuki
Rating:
58

Buy GASKET SET (ALL) 11400-95874 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50M 1980,1981,1982
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    Start By:
Remove the exhaust elbow.
If reusing the exhaust elbow, and or the bellows, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 1 g02346356
Place Mark (X) at all four locations as shown. This action will aid in the installation of the lines group.
Loosen clamp assemblies (1) and (3). Remove lines group (2) .
Illustration 2 g02346357
Failure to follow established procedures can lead to damage of the parts.To avoid damage to the parts, always identify and mark the parts so that the parts can be installed in the same location.
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows if the machine is equipped.Note: If reusing the exhaust elbow, and or the bellows, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Remove both clamp assemblies (5). Remove bellows (6) and position exhaust tube assemblies (4) and (7) aside. Discard clamp assemblies (5) and bellows (6) .
Illustration 3 g02346358
Place Mark (Y) at all four locations as shown. This action will aid in the installation of the lines group.
Remove clamp assemblies (8) and (10), and remove lines group (9) .
Illustration 4 g02346359
Remove both clamp assemblies (12). Remove bellows (13) and position tube assemblies (11) and (14) aside. Discard clamp assemblies (12) and bellows (13) .
Illustration 5 g02346362
Place Mark (Y) at all four locations as shown. This action will aid in the installation of the lines group.
Loosen clamp assemblies (15) and (17) and discard the clamp assemblies. Remove lines group (16) .
Illustration 6 g02346365
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows if the machine is equipped.
Remove both clamp assemblies (19). Remove bellows (20) and position elbow assemblies (18) and (21) aside. Discard clamp assemblies (19) and bellows (20) .
Illustration 7 g02346366
Disconnect tube assembly (22) .
Disconnect tube assemblies (23) and (24) and position the tube assemblies out of the way.
Illustration 8 g02346367
Attach a suitable lifting device to turbocharger (25). The weight of turbocharger (25) is approximately 27 kg (60 lb). Remove nuts (26) and remove the turbocharger. Discard nuts (26) .Installation Procedure
If reusing the exhaust elbow, and or the bellows, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".Note: Check all of the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
The alignment of the bellows is important. Improper alignment may lead to premature failure of the bellows. Misalignment can be identified by visually inspecting the convolutions for uniformity of compression.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. Minor damage to the ends of the bellows may be repaired. However, if there is any difficulty in installation after th


Parts gasket Suzuki:

09168-10004
Gasket, Drain Plug
09168-10004 Gasket, Drain Plug
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20M
65871-93001
 
65871-93001 Gasket, Fuel Gauge
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20M
13392-58600
Gasket, needle valve
13392-58600 Gasket, needle valve
20ELB, 20ELC, 20ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT115, DT140, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150T
13251-95210
 
13251-95210 Gasket, float chamber
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT35TCLH, DT35TCLJ, DT
65561-98502
 
65561-98502 Gasket
25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT15 MLE, DT15ELD, DT15ELE, DT15ELF, DT15ELG, DT15ELH, DT15ESD, DT15ESE, DT15ESF, DT15ESG, DT15ESH, DT15MLD, DT15MLF, DT15MLG, DT15MLH, DT15MSD, DT15MSE, DT15MSF, DT15MSG, DT15MSH, DT16LT, DT16LT, DT16LT, DT16ST, DT
17472-95200
Gasket
17472-95200 Gasket
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT50, DT50M, DT50W, DT60CLD, DT65, DT65, DT
09168-10022
Gasket, Drain Plug
09168-10022 Gasket, Drain Plug
25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15S, DF2.5, DF2.5, DF2.5, DF2.5s, DF25, DF25, DF25(
11400-95872
 
11400-95872 GASKET SET (ENGINE)
DT50, DT50M, DT50W, DT65, DT65
Back to top