13853-95300 Suzuki GASKET

Table 1
Diagnostic Codes Table
J1939 Code and Description Conditions which Generate this Code System Response
91-3
Accelerator Pedal Position #1 : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range. The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed may be limited to high idle.
91-4
Accelerator Pedal Position #1 : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range. The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed may be limited to high idle.
91-8
Throttle Position Sensor abnormal frequency, pulse width, or period The Engine's Electronic Control Module (ECM) detects a sensor frequency that is less than 150 Hz or a sensor frequency that is greater than 1000 Hz for two seconds.
or
The ECM detects a duty cycle that is less than 5 percent or a duty cycle that is greater than 95 percent for one second. The code is logged.
The throttle signal defaults to a zero percent duty cycle (low idle). The speed control is used to provide a throttle signal to the engine control. The output for rated speed is a pulse width modulated signal. The signal varies with the position of the speed adjust potentiometer. The output signal is expressed as a percentage between 0 and 100 percent for the speed adjust potentiometer.The ECM calculates the desired engine speed. The desired engine speed is produced by the signal from the rated speed setting. The rated speed signal is valid when the duty cycle is in the range of 5 to 95 percent. If the rated speed signal is invalid, the engine will be set to the low idle.Some applications may choose not to use the speed control. Some applications may use a load sharing unit. The unit is configured to provide the engine control with a rated speed signal. Some of these units cannot provide a signal until the engine is running. In these cases, perform troubleshooting while the engine is running.
Illustration 1 g03381797
Schematic of the circuit for the speed control
Illustration 2 g03381823
P1 ECM connector
(P1-5) Digital return
(P1-66) Throttle 1
Illustration 3 g03381801
Customer connector
(Terminal 09) Digital return
(Terminal 10) Primary throttle
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect connectors (P1), and (P2). Inspect all of the connectors in the harness from the engine interface connector to the speed control that are associated with the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors, the engine interface connector, and the connector for the EMCP that are associated with the circuit.
D. Check the torque of the allen head screws for each of the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points from the batteries to the ECM.
Connectors
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 2.
Result: The connectors and/or wiring are Not OK.
Repair: Repair the wiring and/or the connectors. Replace parts, if necessary.
Verify that the repair eliminates the problem.
2. Check for Active Diagnostic Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
B. Restore the electrical power to the ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check for an active 08 code for the throttle signal.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Turn the main disconnect switch to the OFF position.
Codes
Result: No diagnostic codes are active.
Repair: If the above code has been logged, there may be an intermittent problem in the harness or in a connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" in order to troubleshoot intermittent electrical problems.
If a problem with the speed control circuit is suspected, proceed to Test Step 3.
Result: A 08 diagnostic code is active at this time. The ECM has detected an erratic signal at the input for the throttle signal.
Proceed to Test Step 3.
3. Check the Supply Voltage to the Speed Control
A. Restore the electrical power to the ECM.
B. Turn the engine control to the ON position.
C. Measure the voltage between terminals +Battery terminal and −Battery terminal of the speed control.
24 3.0 VDC
Result: The supply voltage is 24 3.0 VDC at the speed control. The speed control is receiving supply voltage.
Proceed to Test Step 4.
Result: The supply voltage is not 24 3.0 VDC.
Repair: The supply voltage is not reaching the speed control. If the engine started, the control relay is receiving electrical power. There is a problem in the harness or the connectors between the output of control relay and the speed control. The problem may be in the ground circuit to the speed control.
Perform the following Test Steps:
1. Remove the electrical power from the ECM.
2. Remove the wire from the −Battery terminal at the speed control.
3. Check the resistance between the wire for the −Battery at the speed control and the battery negative post.
The correct measurement will indicate that a short circuit condition exists for the circuit.
If the resistance measurement indicates a short circuit, the ground circuit for the speed control is OK. There is a problem in the harness or the connectors between the control relay and the speed control. Repair the harness and/or the connectors. Replace parts, if necessary. Verify that the original problem has been resolved.
Verify that the repair eliminates the problem.
If the measurement did not indicate a short circuit, the problem is in the ground circuit for the speed control. Repair the harness and/or the connectors. Replace parts, if necessary.
Verify that the repair eliminates the problem.
If the engine does not start, there is a problem in the electrical power supply circuit. Refer to Troubleshooting, "Electrical Power Supply - Test" for details.
4. Check the Throttle Position on Caterpillar Electronic Technician (ET)
A. Observe the position of the throttle on Cat ET.
B.