36663-98J00 Suzuki HARNESS ASSY, ACTIVE HUB PWR S


36663-98J00 HARNESS ASSY, ACTIVE HUB PWR S Suzuki DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF HARNESS

Buy HARNESS ASSY, ACTIVE HUB PWR S 36663-98J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Suzuki entire parts catalog list:

DF100 2009
DF100 2010
DF100 2011
DF100A 2011
DF115 2001,2002,2003,2004,2005,2006,2007,2008,2009
DF115 2010
DF115 2011
DF115A 2011
DF140 2002,2003,2004,2005,2006,2007
DF140 2008,2009,2010
DF140 2011
DF140A 2011
DF140T 2002,2003,2004,2005,2006,2007,2008,2009
DF140T 2010
DF140Z 2002,2004,2005,2006,2007,2009
DF140Z 2003
DF140Z 2008
DF140Z 2010
DF150 2006,2007,2008,2009
DF150 2010
DF150 2011
DF175 2006,2007,2008,2009
DF175 2010
DF175 2011
DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011
DF250A 2011
DF300 2007,2008,2009
DF300 2010
DF300A 2011
DF40 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF40 2010
DF50 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF50 2010
DF60 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF70 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF70A 2009
DF70A 2010
DF80A 2009
DF80A 2010
DF90 2001,2002,2003,2004,2005,2006,2007,2008
DF90A 2009
DF90A 2010

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Excessive Idle or High Load
A. Use Caterpillar Electronic Technician (ET) to check the Current Totals for excessive idle time and/or for a high load factor. These factors would be indicative of poor operating habits.
   
Idle time or load
   
Result: The idle times or load was excessive.
Reduce idle times or load.
Result: The idle times or load was not excessive.
Proceed to Test Step 2.
   
2. Diagnostic Codes
A. Check for logged diagnostic codes or active diagnostic codes. If a diagnostic code is logged or active refer to Troubleshooting, "Diagnostic Trouble Codes" for more information.
   
Codes
   
Result: There are logged or active diagnostic codes.
Troubleshoot any logged or active diagnostic codes before continuing with this procedure. Refer to Troubleshooting, "Diagnostic Trouble Codes" for more information.
Result: There are no logged or active diagnostic codes.
Proceed to Test Step 3.
   
3. Fuel Quality
A. The grade of the fuel affects the rate of fuel consumption. Refer to the engines Operation and Maintenance Manual for additional information.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
   
Fuel quality
   
Result: The fuel quality meets specifications.
Proceed to Test Step 4.
Result The fuel quality does not meet specifications.
Replace the fuel with fuel that meets specifications.
   
4. Calibration Procedure of the Engine Speed/Timing
A. Perform a speed/timing sensor calibration. Refer to the calibration procedure Troubleshooting, "Timing - Calibrate".
   
Calibration
   
Result The speed timing calibration was performed.
Proceed to Test Step 5.
   
5. Unstable Injection Actuation System
A. Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the injector connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
C. Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid - Test".
   
Injection actuation
   
Result The tests completed successfully.
Proceed to Test Step 6.
Result The tests did not complete successfully.
Make the necessary repairs. Verify that the repair resolved the problem.
   
6. Restriction in the Air Inlet and Exhaust
A. Inspect the air filter for a restriction.
B. Check the air inlet and exhaust system for restrictions and/or for leaks.
   
Restrictions
   
Result There are restrictions in the air inlet or exhaust system.
Remove or repair the restrictions.
Result There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 7.
   
7. Check for Damaged Accessory Equipment
A. Check all accessory equipment for problems that may create excessive load on the engine.
   
Accessory equipment
   
Result There is damaged accessory equipment.
Remove or repair the accessory equipment.
   Complete the procedure in the order in which the steps are listed. If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts harness Suzuki:

36610-99E50
 
36610-99E50 HARNESS ASSY, WIRING
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
36610-99E60
 
36610-99E60 HARNESS ASSY, WIRING
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
36610-87JA0
 
36610-87JA0 HARNESS ASSY, WIRING
DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL
36610-87J01
 
36610-87J01 HARNESS ASSY, WIRING
DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL
36610-93JN0
 
36610-93JN0 HARNESS ASSY, WIRING
DF200, DF200, DF225, DF225, DF250, DF250
36610-93JR0
 
36610-93JR0 HARNESS ASSY, WIRING
DF200, DF200, DF225, DF225, DF250, DF250
36610-98J21
36610-98J11
Back to top