11101-93J01 Suzuki HEAD ASSY, CYLINDER STBD


11101-93J01 HEAD ASSY, CYLINDER STBD Suzuki DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z HEAD

Buy HEAD ASSY, CYLINDER STBD 11101-93J01 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Suzuki entire parts catalog list:

DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200T 2004,2005,2006,2007
DF200Z 2004,2005,2006,2007
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225T 2004,2005,2006,2007
DF225Z 2004,2005,2006,2007
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250T 2004,2005,2006,2007
DF250Z 2004,2005,2006,2007

Information:


Illustration 1 g01258295
Schematic
Illustration 2 g01270952
(1) Engine oil level switch
Illustration 3 g01258299
P2 ECM connector
(P2-94) Low oil level
(P2-83) Digital return Test Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connector J2/P2. Inspect the connector for the low oil level switch. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Level of the Engine Oil
Check the engine oil level.
Ensure that the correct engine oil dipstick is installed.
Check for external oil leaks. Expected Result:The engine oil is at the correct level.Results:
OK - The engine oil level is correct. Proceed to Test Step 3.
Not OK - The engine oil level is low.Repair: Add oil to the engine.STOPTest Step 3. Check the Engine Oil Level on Caterpillar Electronic Technician (ET)
Connect Cat ET to the service tool connector.
Turn the keyswitch to the ON position.
Observe the "Engine Oil Level" reading on Cat ET. Expected Result:The "Engine Oil Level" reads "OK".Results:
OK - The "Engine Oil Level" reads "OK".Repair: The switch signal is correct.STOP
Not OK - The "Engine Oil Level" does not read "OK". The switch signal is not correct. Proceed to Test Step 4.Test Step 4. Short the Wires at the Low Oil Level Switch
Disconnect connector J802/P802 of the low oil level switch.
Use a wire to short terminal J802-1 to J802-2. Install the wire jumper on the harness side of the connector.
Turn the keyswitch to the ON position.
Observe the status of the "Engine Oil Level" on Cat ET.
Remove the wire short.
Observe the status of the "Engine Oil Level" on Cat ET.
Turn the keyswitch to the OFF position. Expected Result:Cat ET indicates "OK" when the wire short is installed. Cat ET indicates "LOW" when the wire short is removed.Results:
OK - Cat ET indicates "OK", when the wire short is in place. Cat ET indicates "LOW", when the wire short is removed. Cat ET recognized the input from the switch.Repair: Temporarily replace the switch. Verify that the new switch solves the problem before you permanently install the new switch.STOP
Not OK - Cat ET does not indicate "OK", when the wire short is in place. Cat ET does not indicate "LOW", when the wire short is removed. Cat ET does not recognize the input from the switch. Proceed to Test Step 5.Test Step 5. Short the Input Wires of the Low Oil Level Switch at the ECM Connector
Disconnect ECM connector P2.
Remove the wire from P2-94 (low oil level). Install a wire jumper with a socket on one end into P2-94.
Remove the wire from P2-83 (digital return). Install a wire jumper with a socket on one end into P2-83.
Connect a wire jumper between the wire jumpers in P2-94 and P2-83.
Reconnect all connectors.
Turn the keyswitch to the ON position. The engine should be off. Note: Additional diagnostic codes will be generated because the digital return will no longer be connected to the other sensors and switches. Ignore the codes and clear the codes when you complete this test.
Observe the status of the "Engine Oil Level" on Cat ET.
Turn the keyswitch to the OFF position.
Remove the wire short.
Reconnect all connectors.
Turn the keyswitch to the ON position.
Observe the status of the "Engine Oil Level" on Cat ET.
Turn the keyswitch to the OFF position.
Reconnect all connectors. Expected Result:Cat ET indicates "OK" when the wire short is installed. Cat ET indicates "LOW" when the wire short is removed.Results:
OK - Cat ET indicates "OK", when the wire short is installed. Cat ET indicates "LOW", when the wire short is removed. The harness is faulty.Repair: The ECM is OK. There is a short circuit or there is an open circuit between the ECM and the low oil level switch. Repair the connectors or wiring and/or replace the connectors or wiring.STOP
Not OK - Cat ET does not indicate "OK", when the wire short is in place. Cat ET does not indicate "LOW", when the wire short is removed. The ECM is not reading the switch position.Repair: Replace the ECM. Refer to Troubleshooting, "Replacing the ECM".STOP


Parts head Suzuki:

48630-96J01
HEAD, TRIM CYLINDER
48630-96J01 HEAD, TRIM CYLINDER
DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF225, DF225, DF250, DF250
11101-98J00
 
11101-98J00 HEAD ASSY, CYLINDER STBD
DF200, DF225, DF250, DF300
11101-93J10
11101-93J11
 
11101-93J11 HEAD ASSY, CYLINDER STBD
DF200, DF200, DF225, DF225, DF250, DF250
11101-98J01
 
11101-98J01 HEAD ASSY, CYLINDER STBD
DF200, DF200, DF225, DF225, DF250, DF250, DF300, DF300
11103-93J10
11103-93J02
 
11103-93J02 HEAD ASSY, CYLINDER PORT
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z
11103-98J00
 
11103-98J00 HEAD ASSY, CYLINDER PORT
DF200, DF225, DF250, DF300
Back to top