36616-89L00 Suzuki HOLDER, CONNECTOR


36616-89L00 HOLDER, CONNECTOR Suzuki DF15A, DF20A HOLDER
36616-89L00 HOLDER, CONNECTOR Suzuki
Rating:
68

Buy HOLDER, CONNECTOR 36616-89L00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

DF15A   DF20A   Suzuki

Suzuki entire parts catalog list:

DF15A 2011
DF20A 2011

Information:

1. Remove bolts (2) and pull governor drive (1) from the front drive housing. 2. Make sure the O-ring seals are in position on the front of governor drive (1) and put clean engine oil on the seals.3. Put governor drive (1) in position and install bolts (2) to hold it to the front drive housing.end by:a) install governorDisassemble Governor Drive
start by:a) remove governor drive 1. Remove O-ring seals (1), (2) and (3) from the front of the governor drive housing. 2. Remove the bolts that hold adapter (4) in position and pull adapter (4) from the housing.3. Remove pinion (5), shims (6), seals (7) and (8) from adapter (4). Make a measurement of the thickness of shims (6) and put identification on them for assembly purposes. 4. Remove hose assembly (9), cover (11) and the gasket from governor drive housing (10). 5. Remove gear (13) and coupling (12) from housing (10) as a unit. 6. Remove ring (14) to remove coupling (12) from gear (13). 7. If necessary, remove bearing (15) from housing (10).Assemble Governor Drive
1. Make an alignment of the oil hole in the bearing with the drilled oil passage in governor drive housing (1). Use tool group (A) and install the bearing in housing (1) until it is 1.0 0.5 mm (.039 .020 in.) below the inside surface of the housing. 2. Put coupling (3) in position in gear (2) and install ring (4) to hold the gear and coupling as a unit. 3. Install coupling (3) and gear (2) as a unit in housing (1). 4. Install pinion (5) in adapter (6). 5. Put adapter (6) and shims (7) of the original thickness in position and install the bolts to hold the unit together. 6. Make an adjustment of the gear clearance (backlash) between gear (2) and the pinion as follows: a) Install tool group (B) on gear (2) as shown to check the gear clearance (backlash) at four locations around gear (2) 90° apart.b) Hold the pinion in position and push down while gear (2) is moved back and forth. Make a record of the indications on tool group (B) and use the lowest indication as the correct gear clearance (backlash) value. The correct gear clearance (backlash) is 0.100 + 0.050 or - 0.025 mm (.0039 + .0020 or - .0010 in.).c) Add or subtract shims (7) as necessary until the gear clearance (backlash) is correct.7. Remove tool group (B), the adapter and pinion from the housing. 8. Connect hose assembly (8) to housing (1). Put the gasket and cover (9) in position and install the bolts and washers to hold them to housing (1). 9. Install seals (10) and (11) on adapter (6) and put clean engine oil on them.10. Install the correct amount of shims (7) and adapter (6) with the pinion in housing (1) and tighten the bolts. 11. If necessary, make a replacement of pins (14). Make sure the pins are 14 1 mm (.55 .04 in.) above the surface of the housing.12. Install O-ring seal (12) and seals (13) on the front of the housing. Put clean engine oil on the seals.end by:a) install governor


Parts holder Suzuki:

67256-95600
 
67256-95600 Holder, neutral lock
30ELE, 30ESE, 30MLE, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15A, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF25, DF25(R)S, DF250, DF250, DF250, D
38915-90J00
 
38915-90J00 HOLDER, RELAY
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15A, DF15S, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF25(R)S, DF250,
31173-94J00
 
31173-94J00 HOLDER ASSY, BRUSH
DF15, DF15, DF15, DF15A, DF15S, DF20A, DF25(R)S, DF25R, DF25R, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50A, DF50QH, DF50TL, DF60A, DF60A, DF8A, DF8AR, DF9.9, DF9.9A, DF9.9AR, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99AR, D
67340-99J00
 
67340-99J00 HOLDER, REMOCON CABLE
DF15A, DF20A, DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
51110-89L00
13820-89L00
32890-89L00
65793-89L00
Back to top