51110-99J00 Suzuki HOLDER, ENGINE


51110-99J00 HOLDER, ENGINE Suzuki DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR HOLDER
51110-99J00 HOLDER, ENGINE Suzuki
Rating:
13

Buy HOLDER, ENGINE 51110-99J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Suzuki entire parts catalog list:

DF8A 2011
DF8AR 2010
DF9.9A 2011
DF9.9AR 2010
DF99AR 2010

Information:

Operation of ATAAC
Heated compressed air from the engine turbocharger is conveyed to an air-to-air aftercooler that is positioned in front of the engine radiator. The combined effect of the engine fan and ram air moves cooled air through the aftercooler system to reduce the turbocharged air temperature before it enters the engine intake manifold.Air-to-air aftercoolers can achieve charge air temperatures lower than water-to-air systems for additional efficiency.Lower intake air temperature allows more air to enter the cylinder, resulting in more complete fuel combustion and reduced exhaust emissions.Refer to the "Truck Engine Application and Installation Guide," Form LEBT8121 April, 1988 for more information.
To maintain an adequate water pump cavitation temperature for efficient water pump performance in an Air-to Air Aftercooled engine, Caterpillar recommends that the coolant mix contain a minimum of 30% Caterpillar Antifreeze or equivalent. Only use a greater concentration (above 30%) of ethylene glycol as needed for anticipated ambient temperatures.Ethylene glycol raises the boiling point of water.Do not exceed a coolant mixture of 65% ethylene glycol to water since a concentration above 65% ethylene glycol will reduce the engine's freeze protection and increase the possibility of deposit formation in the cooling system.Dowtherm 209 Full-Fill coolant cannot be substituted for ethylene glycol, due to its inability to raise the water pump cavitation temperature. Dowtherm 209 Full-Fill coolant lowers the boiling point of water.
Winter Fronts
Caterpillar discourages the use of winter fronts or other air flow restriction devices mounted in front of radiators with air-to-air aftercooled engines. Air flow restriction can cause higher exhaust temperatures, power loss, excessive fan usage and a reduction in fuel economy.However, if a winter front must be used, then it should have a permanent circular or diamond-shaped opening directly in line with the fan hub and must have a minimum opening dimension of at least 120 sq. in. (770 sq. cm).A centered opening, versus a side or edge winter front opening is specified to provide sensing when viscous fan drives are used and/or to prevent an interrupted air flow on the fan blades that could cause a fan failure.The greatest need for winter fronts appears to be for trucks parked overnight. At very cold ambient and high winds, insufficient jacket water heat may make the cab uncomfortable for overnight sleeping. Some trucks can be modified to use fully closed winter fronts for overnight sleeping.
Failure to open the winter fronts in the morning could cause engine damage and/or loss of fuel economy.
Caterpillar recommends that a winter front package include an intake manifold temperature warning device such as a temperature light indicator, warning buzzer, etc. to monitor the intake manifold air temperature. The air temperature should not exceed 160°F (70°C) with the winter front installed because of power loss and potential engine damage.Caterpillar also recommends installation of a 4W2682 Indicator (inlet air temperature gauge) to allow the operator to monitor the intake manifold air temperature. For the ATAAC (Air-To-Air Aftercooled) engines, air temperature in the intake manifold should not exceed 160°F (70°C).This temperature provides engine protection for full winter front closure and can serve as a diagnostic tool for a malfunction of the charge air cooling system. It is not anticipated that a temperature of 160°F (70°C) will be encountered under normal operating conditions.Data to evaluate the Air-To-Air Aftercooling system can be obtained from the April, 1988 "Truck Engine Application and Installation Guide," Form LEBT8121.


Parts holder Suzuki:

67256-95600
 
67256-95600 Holder, neutral lock
30ELE, 30ESE, 30MLE, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15A, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF25, DF25(R)S, DF250, DF250, DF250, D
38915-90J00
 
38915-90J00 HOLDER, RELAY
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15A, DF15S, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF25(R)S, DF250,
31173-94J00
 
31173-94J00 HOLDER ASSY, BRUSH
DF15, DF15, DF15, DF15A, DF15S, DF20A, DF25(R)S, DF25R, DF25R, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50A, DF50QH, DF50TL, DF60A, DF60A, DF8A, DF8AR, DF9.9, DF9.9A, DF9.9AR, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99AR, D
13361-99J00
 
13361-99J00 HOLDER, CABLE
DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
21126-99J00
 
21126-99J00 HOLDER, CLUTCH SHAFT
DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
67340-99J00
 
67340-99J00 HOLDER, REMOCON CABLE
DF15A, DF20A, DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
32890-99J00
 
32890-99J00 HOLDER, ELECTRIC PARTS
DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
61642-99J00
 
61642-99J00 HOLDER, FASTENER LEVER
DF8A, DF8AR, DF9.9A, DF9.9AR, DF99AR
Back to top