11293-98J00 Suzuki HOOK, ENGINE


11293-98J00 HOOK, ENGINE Suzuki DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF300, DF300, DF300A HOOK
11293-98J00 HOOK, ENGINE Suzuki
Rating:
8

Buy HOOK, ENGINE 11293-98J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Suzuki entire parts catalog list:

DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011
DF250A 2011
DF300 2007,2008,2009
DF300 2010
DF300A 2011

Information:


Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
267-2 Remote Shutdown Input erratic, intermittent, or incorrect     Both of the switch contacts of the ground level shutdown switch are in the same state.     The code is logged.
The ground level shutdown feature is disabled.    
E265(3) User defined shutdown     The user shutdown switch has been activated.
Certain conditions must be met on some applications prior to the activation of the user defined shutdown switch. These conditions may include setting the parking brake and/or placing the transmission in neutral.     The code is logged.
The engine will be shutdown.    Note: For the E265(3) code, determine if the shutdown was intentional or accidental. If the shutdown was intentional, make sure that the reason for the shutdown has been corrected. Reset the control system. Resume normal operation.The ground level shutdown switch provides the ability to shut down the engine. The engine's Electronic Control Module (ECM) remains active. Caterpillar Electronic Technician (ET) can be used to communicate with the ECM. The ground level shutdown switch must be returned to the Run position and the engine rpm must be zero before the ECM will allow the engine to start.To shut down the engine, lift the red cover guard and toggle the ground level shutdown switch to the Shutdown position. The ECM reads the position of the ground level shutdown switch. If the engine is running, the ECM disables the fuel injection.The ECM will not allow the engine to start if the status for the ground level shutdown switch is "Remote Shutdown". Also, the keyswitch must be cycled before the ECM will allow the engine to start.
Illustration 1 g01395694
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Remove electrical power from the ECM.
Illustration 2 g01139425
ECM (1) J1/P1 connectors (2) J2/P2 connectors
Thoroughly inspect the ECM connector J1/P1. Thoroughly inspect the connectors for the ground level shutdown switch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01395695
P1 ECM connector (P1-2) Shutdown (NO) (P1-8) Shutdown (NC) (P1-29) Return
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the allen head screw from each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ground Level Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector.
Restore electrical power to the ECM.
Observe the status of the ground level shutdown switch on Cat ET.
Operate the ground level shutdown switch. Observe the status of the ground level shutdown switch on Cat ET.Expected Result:The status of the ground level shutdown switch on Cat


Parts hook Suzuki:

11293-93J00
 
11293-93J00 HOOK, ENGINE
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z
11291-93J00
 
11291-93J00 HOOK, ENGINE
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
61641-93J20
 
61641-93J20 HOOK, ENGINE COVER (REAR PORT)
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250
61641-93J10
HOOK, ENGINE COVER (REAR STBD/FRONT)
61641-93J10 HOOK, ENGINE COVER (REAR STBD/FRONT)
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250T, DF250Z
11291-98J00
 
11291-98J00 HOOK, ENGINE
DF200, DF225, DF250, DF250A, DF300A
Back to top