32905-94401 Suzuki Hook, High Tension Cord Clamp


32905-94401 Hook, High Tension Cord Clamp Suzuki DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK Hook
32905-94401 Hook, High Tension Cord Clamp Suzuki
Rating:
103

Buy Hook, High Tension Cord Clamp 32905-94401 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Suzuki entire parts catalog list:

DT35CRLH 1987
DT35CRLJ 1988
DT35CRLK 1989
DT35CRSH 1987
DT35CRSJ 1988
DT35CRSK 1989
DT35MCLH 1987
DT35MCLJ 1988
DT35MCLK 1989
DT35MCSH 1987
DT35MCSJ 1988
DT35MCSK 1989
DT35TCLH 1987
DT35TCLJ 1988
DT35TCLK 1989

Information:


Typical Example1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See the topic, Remove & Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019P4. a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb ft).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.d. Install the rocker shaft assemblies and push rods. See the topic, Install Rocker Shaft Assemblies & Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb ft).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb ft). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb ft).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb ft).5. Install the valve cover bases and the inner fuel lines. See the topic, Install Rocker Shaft Assemblies & Push Rods.6. Install the valve covers. See the topic, Install Valve Covers.
Typical Example7. Install plate (4).8. Connect the water line to the air compressor (if equipped).9. Install bolts (5) for the alternator bracket.End By:a. install exhaust manifoldb. install fuel injection linesc. install aftercooler housingd. install water temperature regulatore. install rocker shaft assemblies and push rods


Parts hook Suzuki:

61631-94410
 
61631-94410 Hook, under cover
DT15ELG, DT15ELH, DT15ELJ, DT15ESG, DT15ESH, DT15ESJ, DT15MLG, DT15MLH, DT15MLJ, DT15MSG, DT15MSH, DT15MSJ, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25C, DT25ELF, DT25ELG, DT25ELH,
61412-96300
 
61412-96300 HOOK, COVER
DT35CRLK, DT35CRSK, DT35MCLK, DT35MCSK, DT35TCLK, DT40C
11291-94401
 
11291-94401 Hook, Engine
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
61631-94400
 
61631-94400 Hook, Engine Cover
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
Back to top