52311-87L00 Suzuki HOUSING, EXHAUST TUBE


52311-87L00 HOUSING, EXHAUST TUBE Suzuki DF70A, DF70A, DF80A, DF80A, DF90A, DF90A HOUSING
52311-87L00 HOUSING, EXHAUST TUBE Suzuki
Rating:
13

Buy HOUSING, EXHAUST TUBE 52311-87L00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

DF70A   DF80A   DF90A   Suzuki

Suzuki entire parts catalog list:

DF70A 2009
DF70A 2010
DF80A 2009
DF80A 2010
DF90A 2009
DF90A 2010

Information:

Start By:a. disassemble governorb. remove fuel injection pumps
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove cover (1) and gasket. 2. Remove rack (2).
If the original lifters are to be installed in the fuel injection pump housing, put identification marks on them as to their location in the housing.
3. Remove lifters (3). 4. Put the fuel injection pump housing on end on blocks. Use tool (A) to remove snap ring (4). 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5). Remove washer (5). 6. Remove camshaft (6). 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear, and put clean oil on all parts before assembly. 1. Use tooling (B) to install bearing (10) in the governor end of the fuel injection pump housing with junction (joint) (11) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (0.10 0.008 in) below the surface of the housing.2. Use tooling (B) to install bearing (9) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (0.282 0.005 in) below the surface of the housing. 3. Use tooling (B) to install bearing (12) in the drive end of the fuel injection pump housing with the junction (joint) in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (9.039 0.010 in) below the surface of the housing. 4. Install plate (13) of tooling (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (14) of tooling (C). Install the driver and bearing in plate (13) with the groove in the driver in alignment with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate (13).5. Remove tooling (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in) below the surface of the housing. 6. Install camshaft (6).7. Put the fuel injection pump housing on end, and place a block under the camshaft. 8. Put washer (5) over the end of the camshaft and use tooling (B) and a spacer (15) that has an inside diameter of 38.1 mm (1.5 in) and a length of 31.75 mm (1.25 in) to push the washer against its seat on the camshaft. Camshaft must have 0.285 0.235 mm (0.0112 0.0093 in) end play when washer is pushed against cam shoulder. 9. Use tool (A) to install snap ring (4). 10. Install six lifters (3) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install rack (2) with the groove in the end of the rack in alignment with the ear (tab) of the rack bearing, at the drive end of the fuel injection pump housing. The six lifters are all the same and can be mixed. 12. Install the gasket and cover (1).End By:a. assemble governorb. install fuel injection pumps
Perform Scheduled Oil Sampling after performing service work to check for fuel leakage and contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.


Parts housing Suzuki:

63111-87J10-0EP
 
63111-87J10-0EP HOUSING, TILLER HANDLE (BLACK)
DF100, DF100, DF100, DF115, DF115, DF115, DF40, DF40, DF40A, DF40A, DF50, DF50, DF50A, DF50A, DF60, DF60A, DF60A, DF70, DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90, DF90A, DF90A, DF90A
25141-87L00
 
25141-87L00 HOUSING, SHIFT ROD GUIDE
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
52111-87L00-0EP
 
52111-87L00-0EP HOUSING, DRIVE SHAFT
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
56120-87L00-0EP
HOUSING, PROP SHAFT BRG
56120-87L00-0EP HOUSING, PROP SHAFT BRG
DF70A, DF70A, DF80A, DF80A, DF90A, DF90A
56120-87L10-0EP
 
56120-87L10-0EP HOUSING, PROP SHAFT BRG
DF70A, DF70A, DF80A, DF80A, DF90A, DF90A
56130-87L00
 
56130-87L00 HOUSING, DRIVE SHAFT OIL SEAL
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
Back to top