56130-98502 Suzuki Housing, Drive Shaft


56130-98502 Housing, Drive Shaft Suzuki DT5LD, DT5SD, DT8LD, DT8LE, DT8LF, DT8SD, DT8SE, DT8SF Housing

Buy Housing, Drive Shaft 56130-98502 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Compatible models:

Suzuki entire parts catalog list:

DT5LD 1983
DT5SD 1983
DT8LD 1983
DT8LE 1984
DT8LF 1985
DT8SD 1983
DT8SE 1984
DT8SF 1985

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
A(2) 585-0005 Crankshaft Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C - E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) This Tool is used in the aperture for the electric starting motor.
(2) The Crankshaft Turning Tool is used on the front pulley.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all the components.
Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the piston and to the bearing shells for the connecting rod.Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g06361356
Install Tooling (B) onto piston (4). Ensure that the piston ring gaps are 120 degrees apart.Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin.Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g06360869
Install connecting rod cap (2) onto connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to connecting rod (3). Use Tooling (C) to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 9 to install the remaining pistons and connecting rods.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts housing Suzuki:

11431-98501
 
11431-98501 Housing, Lower Oil Seal
DT5LC, DT5LD, DT5LN, DT5LT, DT5LX, DT5LZ, DT5SC, DT5SD, DT5SN, DT5ST, DT5SX, DT5SZ, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LG, DT8LH, DT8LT, DT8LX, DT8LZ, DT8SD, DT8SE, DT8SF, DT8SG, DT8SH, DT8ST, DT8SX, DT8SZ
11411-98500
 
11411-98500 Housing, Upper Oil Seal
DT5LC, DT5LD, DT5LN, DT5LT, DT5LX, DT5LZ, DT5SC, DT5SD, DT5SN, DT5ST, DT5SX, DT5SZ, DT6, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LG, DT8LH, DT8LT, DT8LX, DT8LZ, DT8SD, DT8SE, DT8SF, DT8SG, DT8SH, DT8ST, DT8SX, DT8SZ
52110-98513-02M
52110-98524-02M
56110-98502-02M
 
56110-98502-02M Housing, Bearing
DT5LD, DT5SD, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8SD, DT8SE, DT8SF
52110-98514-02M
 
52110-98514-02M Housing, Drive Shaft
DT8LD, DT8LE, DT8LF, DT8SD, DT8SE, DT8SF
52110-98515-02M
 
52110-98515-02M Housing, Drive Shaft
DT6, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LG, DT8LH, DT8SD, DT8SE, DT8SF, DT8SG, DT8SH
52110-98525-02M
 
52110-98525-02M Housing, Drive Shaft
DT8LD, DT8LE, DT8LF, DT8SD, DT8SE, DT8SF
Back to top