19171-93400-01J Suzuki Lever, throttle

System Configuration Parameters
System configuration parameters affect the emissions of the engine or the power of the engine. The parameters are stored in the Engine Control Module (ECM). Use the Caterpillar Electronic Technician (ET) to view the values of the parameters and change the values of the parameters. Refer to Troubleshooting Guide, "System Configuration Parameters" for further information.Customer Configuration Parameters
Customer specified parameters allow the vehicle owner to influence the operating technique of a driver. Some parameters may affect engine operation in a way that would not be expected by an inadequately trained driver. These parameters may lead to power or performance complaints even though the engine's performance is within the engine's specification.Customer parameters may be changed repeatedly as a customer's operation changes or as new drivers are assigned to a truck. Customer passwords are required to change these parameters. The customer password must be programmed into the Engine Control Module (ECM). Refer to Troubleshooting Guide, "Customer Specified Parameters" and refer to Troubleshooting Guide, "Customer Specified Parameters Table" for further information.Worksheet for Customer Specified Parameters
Use the following worksheet in order to record the parameters for your engine.
Table 1
Selected Engine Rating    
Rating Number    
   
Rating Type    
   
Multitorque Ratio    
   
Advertised Power    
   
Governed Speed    
   
Rated Peak Torque    
   
Top Engine Speed Range    
   
Test Spec    
   
Test Spec with BrakeSaver    
   
Table 2
ECM Identification Parameters    
Vehicle ID    
   
Engine Serial Number    
   
ECM Serial Number    
   
Personality Module Part Number    
   
Personality Module Release Date    
   
Table 3
Security Access Parameters    
Total Tattletale    
   
Last Tool to change Customer Parameters    
   
Last Tool to change System Parameters    
   
ECM Wireless Communication Enable    
   
Table 4
Vehicle Speed Parameters    
Vehicle Speed Calibration    
   
Vehicle Speed Cal (J1939 - Trans)    
   
Vehicle Speed Cal (J1939 - ABS)    
   
Vehicle Speed Limit (VSL)    
   
VSL Protection    
   
Tachometer Calibration    
   
Soft Vehicle Speed Limit    
   
Two Speed Axle - Low Speed Range Axle Ratio    
   
Nominal Axle Ratio - High Speed Range Axle Ratio    
   
Table 5
Cruise Control Parameters    
Low Cruise Control Speed Set Limit    
   
High Cruise Control Speed Set Limit    
   
Cruise/Idle/PTO Switch Configuration    
   
Soft Cruise Control    
   
Adaptive Cruise Control Enable    
   
Table 6
Idle Parameters    
Idle Vehicle Speed Limit    
   
Idle RPM Limit    
   
Idle/PTO RPM Ramp Rate    
   
Idle/PTO Bump RPM    
   
Table 7
Dedicated PTO Parameters    
PTO Configuration    
   
PTO Top Engine Limit    
   
PTO Engine RPM Set Speed (0 = Off)    
   
PTO Engine RPM Set Speed    
   
PTO Engine RPM Set Speed A    
   
PTO Engine RPM Set Speed B    
   
PTO to Set Speed    
   
Maximum PTO Enable Speed    
   
PTO Cab Controls RPM Limit    
   
PTO Kickout Vehicle Speed Limit    
   
Max PTO Vehicle Speed    
   
Torque Limit    
   
PTO Shutdown Time (0 = Off)    
   
PTO Shutdown Timer Maximum RPM    
   
PTO Activates Cooling Fan    
   
Table 8
Engine/Gear Parameters    
Lower Gears Engine rpm Limit    
   
Lower Gears Turn Off Speed    
   
Intermediate Gears Engine RPM Limit    
   
Intermediate Gears Turn Off Speed    
   
Gear Down Protection RPM Limit    
   
Gear Down Protection Turn On Speed    
   
Low Idle Engine RPM    
   
Transmission Style    
   
Eaton Top 2 Override with Cruise Switch    
   
Top Gear Ratio    
   
Top Gear Minus One Ratio    
   
Top Gear Minus Two Ratio    
   
Governor Type