50005-94828-02M Suzuki Lower Unit, Complete Long


50005-94828-02M Lower Unit, Complete Long Suzuki DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK Lower
50005-94828-02M Lower Unit, Complete Long Suzuki
Rating:
63

Buy Lower Unit, Complete Long 50005-94828-02M Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 31-2
 

Suzuki entire parts catalog list:

DT35CRLH 1987
DT35CRLJ 1988
DT35CRLK 1989
DT35CRSH 1987
DT35CRSJ 1988
DT35CRSK 1989
DT35MCLH 1987
DT35MCLJ 1988
DT35MCLK 1989
DT35MCSH 1987
DT35MCSJ 1988
DT35MCSK 1989
DT35TCLH 1987
DT35TCLJ 1988
DT35TCLK 1989

Information:

2. Remove the cylinder liners with tool (A) as shown. The Caterpillar pack pulling tools can be used to remove the cylinder liner, piston and connecting rod as a unit. For more detail, see Special Instruction, Form No. SEHS8554.Install Cylinder Liners
1. Clean the cylinder liners and the liner bores in the cylinder block. 2. Install cylinder liners (1) in the block without the O-ring seals or filler band. 3. Check the cylinder liner projection as follows:a. Install the 3/4"-16 NF bolts, 3 in (76 mm) long and the 2F126 Washers of tooling (A) on the cylinder block next to each liner. Tighten the bolts evenly, in four steps: 14 N m (10 lb ft), 35 N m (26 lb ft), 70 N m (50 lb ft) and then turn to 95 N m (70 lb ft).b. Put the adapter plate and one plate of tooling (A) on top of the liner, and install the remainder of tooling (A). Be sure the bar is in position at the center of the liner. Tighten the bolts evenly, in four steps to a torque of 7 N m (5 lb ft), 20 N m (15 lb ft), 35 N m (25 lb ft) then to 70 N m (50 lb ft).c. Check to be sure the distance from the bottom edge of the bar to the top of the cylinder block is the same on both sides of the liner.d. Check the cylinder liner projection with tooling (B) at four locations around the liner. Special instruction, Form No. SMHS7727, is included with the tool.e. Liner projection must be 0.03 to 0.15 mm (.001 to .006 in). Measurements on the same liner must not be different by more than 0.05 mm (.002 in). Average measurements between liners next to each other must not be different by more than 0.05 mm (.002 in).The maximum difference in the average projection for all cylinder liners under one cylinder head must not be more than 0.10 mm (.004 in). If the liner is turned in the bore, it can make a difference in the liner projection. f. If the liner projection is not 0.03 to 0.15 mm (.001 to .006 in), check the thickness of the following parts: spacer plate, spacer plate gasket and cylinder liner flange (3). The thickness of the spacer plate must be 8.59 0.03 mm (.338 .001 in). The thickness of the spacer plate gasket must be 0.20 0.03 mm (.008 .001 in). The thickness of the cylinder liner flange must be 8.890 0.020 mm (.3500 .0008 in). The cylinder liner projection can be changed by the correction of the counterbore in the block to a minimum depth of 0.76 mm (.030 in) with an 8S3140 Cylinder Block Counter Boring Tool. See Special Instruction, Form FM055228. A 5N93 Stainless Steel Insert is also available for use after the cylinder block has been counter bored. Special Instruction, Form No. SMHS82222 has the correct installation procedure for the insert.4. Put a mark on the liner and block so the liner can be installed in the same position from which it was removed.5. Remove tooling (A) and (B). Remove the liner. Install new O-ring seals on the liners. 6. Put liquid soap on the O-ring seals and on the cylinder bores. Put filler band (2) in SAE 30W Oil; then immediately install the filler band on the cylinder liner. Immediately install the cylinder liner in the cylinder block with tooling (C) before expansion of the band.End By:a. install pistons & connecting rod assemblies


Parts lower Suzuki:

50001-94828-02M
 
50001-94828-02M Lower Unit, Complete Short
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
50001-94829-0ED
 
50001-94829-0ED Lower Unit, Complete Short
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
50005-94829-0ED
 
50005-94829-0ED Lower Unit, Complete Long
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
Back to top