13110-90J02 Suzuki MANIFOLD, INTAKE


13110-90J02 MANIFOLD, INTAKE Suzuki DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF90, DF90TL MANIFOLD
13110-90J02 MANIFOLD, INTAKE Suzuki
Rating:
53

Buy MANIFOLD, INTAKE 13110-90J02 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Suzuki entire parts catalog list:

DF100 2009
DF100 2010
DF100 2011
DF115 2001,2002,2003,2004,2005,2006,2007,2008,2009
DF115 2010
DF115 2011
DF115TL 2001,2002,2003,2004,2005,2006,2007
DF140 2002,2003,2004,2005,2006,2007
DF140 2008,2009,2010
DF140 2011
DF140T 2002,2003,2004,2005,2006,2007,2008,2009
DF140T 2010
DF140Z 2002,2004,2005,2006,2007,2009
DF140Z 2003
DF140Z 2008
DF140Z 2010
DF90 2001,2002,2003,2004,2005,2006,2007,2008
DF90TL 2001,2002,2003,2004,2005,2006,2007

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 2 g01131377
Illustration 3 g01158612
Valve bridge for dowel installations
Illustration 4 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
Valve bridge assemblies for dowel installations have an adjustment screw and a jam nut. Use the following procedure to install this configuration.
Loosen adjustment screw (11) and jam nut (12) on bridge assembly (3).
Coat these items with clean engine oil: the dowels, the receptacle of the bridge assembly for the dowels and the uppermost contact surface of bridge assembly (3).
Place bridge assembly (3) into position on the dowel. Apply a downward force of 5 to 45 N (1 to 10 lb) on the uppermost contact surface of bridge assembly (3). While you apply the force, turn adjustment screw (11) until the adjustment screw contacts the valve stem.
Turn the adjustment screw for an additional 20 to 30 degrees (1/3 to 1/2 of the hex).
Hold the adjustment screw in position and tighten jam nut (12) to a torque of 30 4 N m (22 3 lb ft).
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 4.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts evenly to a torque of 215 40 N m (160 30 lb ft).Note: The rocker shaft dowel must be located on the left-hand side of the rocker shaft when installed.
Illustration 5 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread, tighten to a torque of 120 15 N m (89 11 lb ft). If nut (10) is 1/2 inch thread, tighten to a torque of 70 15 N m (52 11lb ft).End By:
Install the valve mechanism cover.


Parts manifold Suzuki:

48400-90J00
 
48400-90J00 MANIFOLD ASSY
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DF90, DF90TL
13110-90J00
 
13110-90J00 MANIFOLD, INTAKE
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF90, DF90TL
13110-90J01
 
13110-90J01 MANIFOLD, INTAKE
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF90, DF90TL
48503-92J01
 
48503-92J01 MANIFOLD SUB ASSY
DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z
48641-92J00
 
48641-92J00 MANIFOLD, PTT
DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z
48641-96J01
 
48641-96J01 MANIFOLD, PTT
DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF225, DF225, DF250, DF250
Back to top