33920-99E72 Suzuki MODULE, ENGINE CONTROL


33920-99E72 MODULE, ENGINE CONTROL Suzuki DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL MODULE
33920-99E72 MODULE, ENGINE CONTROL Suzuki
Rating:
58

Buy MODULE, ENGINE CONTROL 33920-99E72 Suzuki genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$2,074.70
 

25-12-2020

-: -
Suzuki Boat Engine Control Unit 33920-99E72 | Df60 Model 03 06
Boat Manufacturer: Unavailable; Part Manufacturer: Suzuki; Part Number: 33920-99E72; Color: Black; Finish: Matte; Overall Dimensions: 4 3/8Inch L X 4 3/8Inch W; Connection: 44 Pin Male;
Number on catalog scheme: 12
 

Compatible models:

Suzuki entire parts catalog list:

DF60 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF60HL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF60TL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF70 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF70THL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007
DF70TL 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007

Information:


Illustration 1 g00671263
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J2/P2 ECM connector, the J3/P3 machine connector, and the J113/P113 power shift solenoid connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Inspect the following components for damage, corrosion, and incorrect attachment:
Battery posts
Alternator
Breaker
Engine ground
Chassis groundExpected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and that the connectors are completely coupled.Verify that the repair eliminates the problem. Stop.Test Step 2. Perform the "Power Shift Pressure Solenoid Test"
Turn the keyswitch to the OFF/RESET position.
Disconnect the J113/P113 Power shift solenoid connector.
Connect Cat ET to the data link connector.
Turn the keyswitch to the ON position.
Activate the "Power Shift Pressure Solenoid Test" on Cat ET.
Use a voltage test lamp between the two terminals of the J113/P113 Power shift solenoid connector.Expected Result:The voltage test lamp illuminated when the "Power Shift Pressure Solenoid Test" was activated on Cat ET.Results:
OK - The voltage test lamp illuminated. Proceed to Test Step 3.
Not OK - The voltage test lamp did not illuminate. Proceed to Test Step 4.Test Step 3. Check the Solenoid for an Internal Short or Open
Disconnect the J113/P113 Power shift solenoid connector.
Measure the resistance between P113:1 and P113:2.Expected Result:The resistance is between 7 Ohms and 17 Ohms.Results:
OK - Proceed to Test Step 4.
Not OK - The solenoid is faulty.Repair: Replace the solenoid.Verify that the repair eliminates the problem. Stop.Test Step 4. Check the Resistance Through the Harness
Illustration 2 g00671736
ECM connector P2 (wire side)
Disconnect the J2/P2 ECM connector.
Use a suitable piece of wire to short P2:13 (Power Shift Solenoid) to P2:7 (Solenoid Return).
Measure the resistance between J113:1 and J113:2.
Remove the wire short.Expected Result:The resistance is less than 10 Ohms.Results:
OK - Proceed to Test Step 5.
Not OK - There is an open circuit or there is excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 5. Check For Shorts In Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect the J2/P2 ECM connector and the J113/P113 Power shift solenoid connector.
Measure the resistance between engine ground and each terminal of J113 Power shift solenoid connector.
Measure the resistance between both terminals of J113 Power shift solenoid connector.Expected Result:Resistance is greater than 20,000 Ohms for each reading.Results:
OK - Proceed to Test Step 6.
Not OK - There is a short in the harness between the ECM and the power shift solenoid.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 6. Check the Voltage for the Solenoid at the ECM
Reconnect all connectors.
Connect Cat ET to the data link connector.
Start the engine.
Ensure that the keyswitch is in the ON position.
Check for any active diagnostic codes.Expected Result:The following diagnostics are not active:
581:05 Power Shift Solenoid open circuit
581:06 Power Shift Solenoid short to groundResults:
OK - The solenoid and the harness are OK.Repair: If the system does not function properly refer to Troubleshooting, "Unstable Hydraulic Function". Stop.
Not OK - The ECM is faulty.Repair: Replace the ECM. Refer to Troubleshooting, "Replacing the ECM".Verify that the repair eliminates the problem. Stop.


Parts module Suzuki:

33920-99EA0
 
33920-99EA0 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E91
 
33920-99E91 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E05
 
33920-99E05 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E14
 
33920-99E14 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E73
 
33920-99E73 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E83
 
33920-99E83 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E81
 
33920-99E81 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
33920-99E82
 
33920-99E82 MODULE, ENGINE CONTROL
DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
Back to top