09285-17002 Suzuki Oil Seal

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Clean the cooling system and flush the cooling system before the recommended maintenance interval if the following conditions exist:
The engine overheats frequently.
Foaming of the coolant
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.Note: When the cooling system is cleaned, only clean water is needed when the ELC is drained and replaced.Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator and the hoses, if necessary. Drain
Illustration 1 g01355994
Stop the engine and allow the engine to cool. Loosen expansion tank filler cap (1) slowly in order to relieve any pressure. Remove the expansion tank filler cap.
Open the cooling system drain valve (if equipped).
In order to fully drain the coolant, remove the following plugs:
Remove plug (2) in order to vent the water near the water temperature regulator.
Illustration 2 g01637916
Pleasure craft
Remove drain plug (3) from the bottom heat exchanger.
Illustration 3 g01355996
Remove drain plug (4) from the bottom of the water cooled exhaust manifold.
Remove drain plugs (5) from the bottom of the jacket water pump inlet.
Remove drain plug (6) from the bottom of the oil cooler.
Allow coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
International 1-309-578-7372
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Reinstall the drain plugs. Refer to the Operation and Maintenance Manual for more information on the proper torques.
Fill the cooling system with clean water. Reinstall the expansion tank filler cap. Operate the engine until the temperature reaches 49 to 66°C (120 to 150°F).
Stop the engine and allow the engine to cool. Loosen the expansion tank filler cap slowly in order to relieve any pressure. Remove the expansion tank filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water.
If necessary, repeat step 2 through step 4. Fill
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the expansion tank with the ELC. Do not reinstall the expansion tank filler cap.
Start and run the engine at low idle. Increase the engine rpm to 1500 rpm. Run the engine at 1500 rpm for one minute in order to purge the air from the cavities of the engine block. Stop the engine.
Check the coolant level. Maintain the coolant level within 13 mm (0.5 inch) below the bottom of the pipe for filling. Maintain the coolant level within 13 mm (0.5 inch) to the proper level on the sight glass (if equipped).
Clean the expansion tank filler cap. Inspect the gasket of the filler cap for the expansion tank. If the gasket is damaged, discard the old expansion tank filler cap and install a new expansion tank filler cap. If the gasket is not damaged, use a 9S-8140 Pressurized Pump Group in order to pressure test the expansion tank filler cap. The correct pressure for the filler cap of the expansion tank is stamped on the face of the filler cap for the expansion tank. If the expansion tank filler cap does not retain the correct pressure, install a new expansion tank filler cap.
After the cooling system has been filled, perform the following procedures during initial start-up:.
Start the engine without the filler cap.
Run the engine at low idle for ten minutes.
Then, increase the engine speed to a high idle until the thermostat is open and the coolant level is stabilized.
Maintain the coolant at the proper level as the thermostat opens and air is purged from the system. Refer to Operation and Maintenance Manual, "Cooling System Coolant Level - Check".