18131-93000 Suzuki Pawl, drive


18131-93000 Pawl, drive Suzuki 20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M Pawl
18131-93000 Pawl, drive Suzuki
Rating:
8

Buy Pawl, drive 18131-93000 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Suzuki entire parts catalog list:

20ELB 1977
20ELC 1978
20ELN 1979
25ELB 1977
25ELC 1978
25ELN 1979
25ELT 1980
25ELX 1981
DT20ESB 1977
DT20ESC 1978
DT20ESN 1979
DT20MLB 1977
DT20MLC 1978
DT20MLN 1979
DT20MSB 1977
DT20MSC 1978
DT20MSN 1979
DT25ELZ 1982
DT25ESB 1977
DT25ESC 1978
DT25ESN 1979
DT25EST 1980
DT25ESX 1981
DT25ESZ 1982
DT25MLB 1977
DT25MLC 1978
DT25MLN 1979
DT25MLT 1980
DT25MLX 1981
DT25MLZ 1982
DT25MSB 1977
DT25MSC 1978
DT25MSN 1979
DT25MST 1980
DT25MSX 1981
DT25MSZ 1982
DT28F 1979
DT28G 1980
DT28J 1981
DT28Z 1982

Information:

Introduction
This Special Instruction details the fabrication of parts, rework of the engine hood, and installation of parts to equip the listed machines with a precleaner for air going to the engine air filters.Do not perform the procedures that are outlined in this Special Instruction until you understand the information that is contained in this document.Safety
Dust generated when grinding or cutting nonmetallic materials may be very fine, abrasive, flammable, and/or explosive. Material being removed may contain crystalline silica, quartz, glass fibers, and other fine materials. Prolonged breathing of the dust may cause cancer and irreversible lung damage. Wear goggles, gloves, and a dust respirator certified by the National Institute for Occupational Safety and Health (NIOSH) and by the Mine Safety and Health Administration (MSHA).In the event of contact with the skin, flush the skin with plenty of water. If dust material gets into the eyes, flush the eyes with an approved flushing system and seek medical attention. Before smoking or eating, clean hands thoroughly. Keep the work site clean and dispose of all dust and particles in containers approved for flammable materials.Refer to the dust handling instructions in this publication for correct disposal of the dust.
Paint and products used in painting may be flammable and hazardous. Read, understand, and follow instructions for use on the container. Wear NIOSH/MSHA certified respiratory protection.
Reference
Special Instruction, REHS1841, "General Welding Procedures"Operation and Maintenance Manual, "Hood Control"Operation and Maintenance Manual, "Engine Air Filter Primary Element - Clean/Replace"Required Parts
Table 1
Required Parts    
Item    Qty    Description    
1     1     Air Intake Cover    
2     1     Guard and Tube (External)    
3     1     Flange    Table 1 lists the parts that must be fabricated before a precleaner can be installed. Refer to ""Fabrication of Parts for the Precleaner"".
Table 2
Required Parts    
Item    Qty    Part Number    Description    
4     1     130-3281     Precleaner As    
5     8     6V-7357     Bolt    
6     8     9X-6165     Washer    
7     1     8T-4990     Hose Clamp    
8     1     124-2456     Film    
9     2     9U-7073     Tapered Cap/Plug    
10     4     9U-7069     Tapered Cap/Plug    Table 2 lists the standard parts that must be obtained before a precleaner can be installed.
Table 3
Consumables    
CAT Paint Primer    
CAT Black Paint    
CAT Yellow Paint    
Sealant    
Teroson PU 92 (Terostat 92) (Polyurethane-based adhesive sealant)    
Thread Lock (Loctite 242)    Table 3 lists the consumables that must be obtained before a precleaner can be installed.Fabrication of Parts for the Precleaner
Air Intake Cover
Illustration 1 g03777624
Air Intake Cover (1) (A) 170.5 mm (6.72 inch) (B) 170.5 mm (6.72 inch) (C) 2700 mm (106.30 inch) radius (D) 1.2 mm (0.05 inch) (E) 32 mm (1.26 inch) (F) 38 mm (1.50 inch) (G) 2800 mm (110.24 inch) radius (H) 151.5 mm (5.96 inch) (J) 151.5 mm (5.96 inch) (K) 38 mm (1.50 inch) (L) 32 mm (1.26 inch) (M) 18 mm (0.71 inch) radius (x4)
Fabricate Air Intake Cover (1) from 1.2 mm (0.05 inch) thick steel plate. Refer to Illustration 1
Paint the air intake cover with CAT primer and CAT yellow paint.Guard and Tube External
Fabrication of Plate 1 (F1)
Illustration 2 g03857168
Fabrication of Plate (carbon steel) 3 mm (0.12 inch) thick (C1) Diameter 206 mm (8.11inch) (C2) Diameter 6.5 mm (0.26 inch) times eight (D1) 45.2 mm (1.78 inch) times four (D2) 109 mm (4.30 inch) times four (D3) 62.3 mm (2.453 inch) (D4) 45.2 mm (1.78 inch) times four (D5) 11.1 mm (0.44 inch) (D6) 3 mm (0.12 inch) (R1) Radius 220 mm (8.66 inch) (R2) Radius 208.3 mm (8.2 inch) (R3) Radius 134 mm (5.28 inch) (R4) Radius 5 1 mm (0.20 0.04 inch) times twoFollow the information in Illustration 2 to fabricate plate 1 (F1) .


Back to top