09206-11006 Suzuki Pin

Table 1
Diagnostic Codes Table    
Code and Description     Conditions which Generate this Code     System Response    
569-5 Oil Injection Solenoid current below normal     The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery in the circuit for the oil renewal solenoid.     The code is logged. The oil renewal system is disabled.    
569-6 Oil Renewal Solenoid short to ground     The ECM detects a short circuit to ground in the circuit for the oil renewal solenoid.    
E2089(1) Oil Renewal System Cannot Operate     A 569-5 Oil Injection Solenoid current below normal is active.
or
A 569-6 Oil Renewal Solenoid short to ground is active.
or
The ECM detects a fault in the circuit for the coolant temperature sensor.
or
The ECM detects a fault in the circuit for the fuel level sensor.
or
The ECM detects a fault in the circuit for the oil pressure sensor.    The ECM adds a controlled amount of engine oil to the fuel by energizing the oil renewal solenoid. The engine oil is added to the fuel and burned during combustion. The typical oil change interval may be extended.For further information, refer to Service Manual, RENR2223, "Oil Renewal System".
Illustration 1 g01439943
Schematic for the oil renewal system
Illustration 2 g01440000
Location of the oil renewal solenoid (typical right side engine view)
Illustration 3 g01440026
Location of the connectors that are for the sensor signal circuit (left side engine view) (1) J2/P2 ECM connector (2) Right rail connector (3) J1/P1 ECM connector
Illustration 4 g01440005
Terminal locations at the P1 ECM connector for the oil renewal solenoid (P1-11) Oil renewal solenoid
Illustration 5 g01440007
Terminal locations at the P2 ECM connector for the oil renewal solenoid (P2-14) Digital return
Illustration 6 g01440023
Terminal locations at the right rail connector for the oil renewal solenoid (Terminal 3) Return (Terminal 69) Oil renewal solenoid
Illustration 7 g01155187
Terminal locations at the connector for the oil renewal solenoid (1) Signal (2) Return
Table 2
Troubleshooting Test Steps    Values    Results    
1. Inspect the Electrical Connectors and the Wiring
A. Remove the electrical power from the engine ECM.
B. Thoroughly inspect the J1/P1 and J2/P2 ECM connectors. Inspect all of the other connectors that are in the circuit for the oil renewal solenoid. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
D. Check the allen head screw on each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points.
    Inspect Connectors and Wiring    
Results: The harness and wiring appear to be OK.
Proceed to Test Step 2.
Results: There is a problem in the connectors and/or wiring.
Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
Verify that the repair eliminates the problem.
   
2. Check for Active Diagnostic Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
B. Restore the electrical power to the engine ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Select diagnostic tests from Cat ET.
E. Select the "Override Parameters" screen on Cat ET.
F. Activate the override for the oil renewal solenoid.
G. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
H. Disable the override for the oil renewal solenoid.
I. Remove the electrical power from the engine ECM.
J. Determine if the problem is related to an open circuit diagnostic code -5 or a short circuit diagnostic code -6.
    Active Code    
Results: No diagnostic codes are active.
Repair: There does not appear to be a problem with the oil renewal solenoid at this time. The problem may have been related to an intermittent electrical problem in the harness or in a connector. If an intermittent electrical problem is suspected, carefully inspect the connectors and wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Results: A short circuit diagnostic code -6 is active at this time.
Proceed to Test Step 3.
Result: An open circuit diagnostic code -5 is active at this time.
Proceed to Test Step 4.
   
3. Disconnect the Connector for the Oil Renewal Solenoid in order to Create an Open Circuit
A. Disconnect the connector