18191-93100 Suzuki Plate, Guide


18191-93100 Plate, Guide Suzuki DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ Plate
18191-93100 Plate, Guide Suzuki
Rating:
53

Buy Plate, Guide 18191-93100 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 12-2
 

Suzuki entire parts catalog list:

DT16LT 1980
DT16LT 1981
DT16LT 1982
DT16ST 1980
DT16ST 1981
DT16ST 1982
DT9.9LT 1980
DT9.9LX 1981
DT9.9LZ 1982
DT9.9ST 1980
DT9.9SX 1981
DT9.9SZ 1982

Information:


Table 1
J1939 Code and Description CDL Code and Description System Response
970-0
Engine Auxiliary Engine Shutdown Switch : High - most severe (3) 337-2
Remote Emergency Stop Switch : Erratic, Intermittent, or Incorrect The two inputs from the emergency stop switch are in the opposite state.
The code is logged.
2813-5
Engine Air Shutoff Command Status : Current Below Normal 446-5
Air Shutdown Relay : Current Below Normal The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery in the solenoid circuit.
The code is logged.
2813-6
Engine Air Shutoff Command Status : Current Above Normal 446-6
446-6 Air Shutoff Relay short The ECM detects a short circuit to ground in the solenoid circuit.
The code is logged.
Illustration 1 g01827000
Schematic for the air shutoff system if equipped with an A4 ECM
Illustration 2 g06325126
Schematic for the air shutoff system if equipped with an A5 ECM
Table 2
Troubleshooting Test Step Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the battery disconnect switch to the OFF position.
B. Verify that the air shutoff mechanisms are set to the OPEN position.
C. Thoroughly inspect the electrical connectors and switches for the air shutoff that are on both sides of the engine. Refer to Troubleshooting, "Electrical Connectors - Inspect"
D. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit for the air shutoff system.
E. Check the allen head screw on each ECM connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
F. Check the harness and the wiring for abrasion and for pinch points from the air shutoff solenoid to the ECM.
Connectors
Results: The connectors and wiring appear to be OK.
Proceed to Test Step 2
Results: The connectors and/or wiring are not OK.
Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all the seals are properly in place and ensure that the connectors are coupled. Verify that the problem is resolved.
Table 3
Troubleshooting Test Step Values Results
2. Test the Operation of the Control Solenoid for the Air Shutoff Relay and Check for Logged Codes
A. Connect Cat ET to the service tool connector.
B. Turn the battery disconnect switch to the ON position.
C. Test the air shutoff system with the emergency stop switch:
a. Start the engine.
b. Place the emergency stop switch in the STOP position.
c. Check the position of the air shutoff mechanisms. Activation of the emergency stop will activate the air shutoff system and the air shutoff mechanisms will close.
Check that the solenoid has de-energized after the air shutoff mechanisms are closed.
d. Turn the battery disconnect switch to the OFF position.
D. Check the status of the "Air Intake Shutoff Position" parameter in Cat ET.
a. While both of the air shutoff mechanisms are shut, check the status of "Air Intake Shutoff Position" by using Cat ET.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
b. Reset the right air shutoff mechanism. Check the status of the "Air Intake Shutoff Position" parameter in Cat ET while the left air shutoff is closed.
c. Reset the left air shutoff mechanism. Check the status of the "Air Intake Shutoff Position" parameter in Cat ET while the left air shutoff mechanism is closed.
E. Use Cat ET to check for logged diagnostic codes. Check if the following codes are logged:
- 337-2
- 446-5
- 446-6
F. Reset both of the air shutoff mechanisms for the air shutoff to the open position.
Restore the wiring


Parts plate Suzuki:

41311-93000
 
41311-93000 Plate, Clamp Bracket
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20M
21112-93200
 
21112-93200 Plate, Clutch Lever
DT14C, DT14D, DT14F, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
21121-93300
 
21121-93300 Plate
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50A, DF50QH, DF50TL, DF60, DF60A, DF60A, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DT115, DT140, DT14C, DT14D, DT
14131-93101
 
14131-93101 Plate, Exhaust Cover
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
41213-93001
 
41213-93001 PLATE, CLAMP
25ELT, 25ELX, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT25ELZ, DT25EST, DT25ESX, DT25ESZ, DT25MLT, DT25MLX, DT25MLZ, DT25MST, DT25MSX, DT25MSZ, DT28G, DT28J, DT28Z, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35M
21313-93100
 
21313-93100 Plate, Interlock
DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
14131-93990
 
14131-93990 Plate, Exhaust Cover
DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
14131-93102
 
14131-93102 Plate, Exhaust Cover
DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
Back to top