43118-96J00 Suzuki PLATE, TRIM SENDER CAM


43118-96J00 PLATE, TRIM SENDER CAM Suzuki DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250 PLATE
43118-96J00 PLATE, TRIM SENDER CAM Suzuki
Rating:
93

Buy PLATE, TRIM SENDER CAM 43118-96J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Suzuki entire parts catalog list:

DF150 2006,2007,2008,2009
DF150 2010
DF150 2011
DF150TX 2006,2007
DF150ZX 2006,2007
DF175 2006,2007,2008,2009
DF175 2010
DF175 2011
DF175TX 2006,2007
DF175ZX 2006,2007
DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011

Information:


Table 1
Event Code
Code and Description Conditions which Generate this Code System Response
E361(1) High Engine Coolant Temperature The engine coolant temperature has exceeded the trip point and the delay time has expired. The code is logged.
E361(2) High Engine Coolant Temperature The engine coolant temperature has exceeded the trip point and the delay time has expired. Engine power is derated. The code is logged.
The derate is 25 percent for every degree over the trip point. The maximum derate is 100 percent.
E361(3) High Engine Coolant Temperature The engine coolant temperature has exceeded the trip point and the delay time has expired. Probable Causes
Low coolant level and/or coolant leakage
Water temperature regulator and/or pressure relief valve
Radiator or heat exchanger
Engine cooling fan (if equipped)
Coolant pump
Coolant temperature sensorRecommended Actions
Coolant
Inspect the coolant level. If necessary, add coolant.
Check the mixture of antifreeze and water. Refer to Operation and Maintenance Manual.
Check the cooling system for leaks. Repair any leaks immediately.
Check for air in the cooling system. Refer to Systems Operation/Testing and Adjusting for the correct procedure. Water Temperature Regulator and/or Pressure Relief Valve
Pressure test the cooling system. Refer to Systems Operation/Testing and Adjusting for the correct procedure.
Check that the seating surfaces of the pressure relief valve and the radiator cap are clean and undamaged.
Check operation of the pressure relief valve and/or the water temperature regulator. If necessary, clean the components and/or replace the components. Radiator or Heat Exchanger
Radiator
Check the radiator fins for dirt, debris, and/or damage. Remove any dirt and/or debris and straighten any bent fins. Check for collapsed hoses and/or other restrictions.
Check the radiator for internal blockage. Refer to Systems Operation/Testing and Adjusting for more information. Heat Exchanger
Check for sufficient flow and temperature of the cooling water through the heat exchanger. If the flow of cooling water through the heat exchanger is insufficient, determine the location of the obstruction. If the temperature of the cooling water is too high, determine the cause. Make the necessary repairs.Faulty Engine Cooling Fan (if equipped)
If the fan is belt driven, check for loose drive belts. A loose fan drive belt will cause a reduction in the air flow across the radiator. Check the fan drive belt for proper belt tension. Adjust the tension of the fan drive belt, if necessary. Refer to Operation and Maintenance Manual.
Check the fan clutch, if equipped. A fan clutch or a hydraulic driven fan that is not turning at the correct speed can cause improper air speed across the radiator core. The lack of proper air flow across the radiator core can cause the coolant not to cool to the proper temperature differential. Coolant Pump
Inspect the impeller of the coolant pump for damage and/or erosion.
Make sure that the drive gear is not loose on the drive shaft of the coolant pump.
If necessary, replace the coolant pump. Refer to Disassembly and Assembly for the correct procedure. Check the Coolant Temperature Sensor and/or the Circuit
Check the reading of the coolant temperature on Cat ET. The temperature should rise steadily as the engine is warmed. Ensure that the temperature is reasonable.If the reading on Cat ET for the coolant temperature is not reasonable, troubleshoot the circuit and the coolant temperature sensor. Refer to Troubleshooting, "Sensor Signal (Analog, Passive) - Test".


Parts plate Suzuki:

37823-92E01
PLATE
37823-92E01 PLATE
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140A, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15A, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF2.5, DF2.5, DF2.5, DF2.5s, DF200, DF200, DF200, DF200T, DF200Z,
31152-90J00
 
31152-90J00 PLATE, CENTER
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15A, DF15S, DF175, DF175, DF175, DF175TX, DF175
16551-93J00
 
16551-93J00 PLATE, OIL CONTROL
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250T, DF250Z
41117-93J00
 
41117-93J00 PLATE, CLAMP BRKT LOWER STBD
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z, DF300, DF300
41117-93J01
 
41117-93J01 PLATE, CLAMP BRKT LOWER STBD
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF300, DF300, DF300A
41122-93J00
 
41122-93J00 PLATE, CLAMP BRKT LOWER PORT
DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250T, DF250Z, DF300, DF300
41118-96J00
 
41118-96J00 PLATE, TRIM SENDER
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250
11270-93J00
 
11270-93J00 PLATE, CYL BLOCK WTR JKT
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
Back to top