09247-25001 Suzuki Plug, Fuel Drain

Illustration 1 g00103219
Never bend the eyebolts and the brackets. Only load the eyebolts and the brackets under tension. Remember that the capacity of an eyebolt is less as the angle between the supporting members and the object becomes less than 90 degrees.When it is necessary to remove a component at an angle, only use a link bracket that is properly rated for the weight.
Use a hoist to remove heavy components. Use an adjustable lifting beam to lift the engine or lift the transmission. All supporting members (chains and cables) should be parallel to each other. The chains and cables should be perpendicular to the top of the object that is being lifted. Some removals require lifting the fixtures in order to obtain proper balance and safety.To remove the engine only, use the lifting eyes that are on the engine. To lift the transmission only, use the lifting eyes that are on the transmission.Lifting eyes are designed and installed for the specific engine arrangement. Alterations to the lifting eyes and/or the engine make the lifting eyes and the lifting fixtures obsolete. If alterations are made, ensure that proper lifting devices are provided. Consult your Caterpillar dealer for information regarding fixtures for proper engine lifting.Lifting the Transmission
For lifting objects, use properly rated cables and properly rated slings. Position the crane for a level lift of the transmission. Consult your Caterpillar dealer for information regarding fixtures for proper lifting of your transmission.TH48FT Transmission
Illustration 2 g01521219
TH48FT front view of the transmission
(1) Lifting eyes
Illustration 3 g01521225
Rear view
(1) Lifting eyes
Illustration 4 g01521233
TH48FT right side view of the transmission
(1) Lifting eyes The weight of the TH48FT transmission is approximately 1802 kg (3973 lb).CX35-P800 Transmission
Illustration 5 g01849934
Lift angles that are less than 60° from horizontal are not acceptable.
Use a hoist to remove heavy components. Use an adjustable lifting beam to lift the transmission. All supporting members (chains and cables) should be parallel to each other. The chains and cables should be perpendicular to the top of the object that is being lifted. Alterations to lifting eyes or fixtures will make lifting eyes and fixtures obsolete. Eyebolts are not recommended for lifting this transmission. Suitable lifting rings are recommended.Acceptable lifting points. The guard for the ECPC valve should be mounted on the transmission if the transmission is being placed on the base supports.Care must be taken when the transmission is lifted in order to avoid damaging the following components that are mounted externally on the transmission: ECU, ECPC valves, solenoids, wire harness and sensors.Some removals require lifting fixtures in order to obtain proper balance and safety. For lifting objects, use properly rated cables and properly rated slings. Position the crane for a level lift of the transmission. Consult your Caterpillar dealer for information regarding fixtures for proper lifting of your transmission.Spreader bar widths should be sufficient for preventing contact with the transmission.
Illustration 6 g01965098
CX35–P800 Petroleum Transmission
(1) Threaded holes Lifting points (1) can be used to tie down the transmission. Install the tie-downs at all locations.The weight of the CX35–P800 Petroleum Transmission with a dry sump is approximately 630 kg (1390 lb).Install appropriate lifting devices in threaded holes (1). The weight of the transmission and attachments must be considered when the lifting device is selected.
Illustration 7 g01965099
CX35–P800 Petroleum Transmission with integral pump
(1) Threaded holes
(2) Lifting eye Lifting points (1) and (2) can be used to tie down the transmission. Install the tie-downs at all locations.The weight of the CX35–P800 Petroleum Transmission with an integral pump and with a dry sump is approximately 731 kg (1611 lb).Install appropriate lifting devices in threaded holes (1). The weight of the transmission and attachments must be considered when you select the lifting device.Lifting the Engine
To remove the engine only, use the lifting eyes that are on the engine.
Illustration 8 g01521273
Typical examples of an industrial engine and a petroleum engine
(1) Engine lifting eyes Lifting the Petroleum Package
Do not use the lifting eyes for the engine, or the lifting eyes for the transmission to lift the entire package. Lifting the entire package may require special equipment and procedures. Consult your Caterpillar dealer for information regarding the proper equipment and procedures to lift the entire package.