18498-94J30 Suzuki PROTECTOR (L:340)


18498-94J30 PROTECTOR (L:340) Suzuki DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH PROTECTOR
18498-94J30 PROTECTOR (L:340) Suzuki
Rating:
23

Buy PROTECTOR (L:340) 18498-94J30 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Suzuki entire parts catalog list:

DF15 2004,2005,2006,2007,2008,2009
DF15 2010
DF15S 2004,2005,2006,2007
DF9.9R 2004,2005,2006,2007,2008,2009
DF9.9RL 2004,2005,2006,2007
DF9.9S 2004,2005,2006,2007
DF9.9TH 2008
DF9.9TH 2009,2010
DF99R 2004,2005,2006,2007,2008,2009
DF99TH 2008,2009,2010

Information:


Illustration 1 g01205508
Schematic for the ECS with EMCP 3
Test Step 1. Check for Connector Damage.
Set the EMCP 3 to the STOP position.
Turn the battery disconnect switch to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are okay. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not okay.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring.STOPTest Step 2. Check for a CID-FMI.
Connect the Caterpillar Electronic Technician (ET).
Turn the battery disconnect switch to the ON position.
Set the EMCP 3 to the STOP position.
Observe the logged diagnostic codes on Cat ET.
Observe the status screen on Cat ET. Expected Result:Cat ET indicates a CID-FMI 336-02.Cat ET indicates that the status for the Engine Control Switch is "Abnormal/Incorrect Data".Results:
OK - Cat ET indicates a CID-FMI 336-02 and Cat ET indicates that the status for the Engine Control Switch is "Abnormal/Incorrect Data". Proceed to Test Step 3.
Not OK - Cat ET does not indicate a CID-FMI 336-02 and "Abnormal/Incorrect Data".Repair: The problem may be intermittent. If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors".STOPTest Step 3. Check the Wiring for an Open Condition
Turn the EMCP 3 to the STOP position.
Turn the battery disconnect switch to the OFF position.
Disconnect the J1/P1 ECM connector.
Check for continuity between P1-22 start/run/stop 2 and P1-21 start/run/stop 1 with a resistance measurement. Expected Result:A short circuit condition exists.Results:
OK - A short circuit condition exists. Proceed to Test Step 4.
Not OK - A short circuit condition does not exist between P1-22 and P1-21.Repair: There is an open circuit between P1-22 and P1-21. Repair the wires or replace the wires between P1-22 and P1-21. Verify that the problem has been resolved.STOPTest Step 4. Check ECM For Proper Operation
Remove the wire F716 from P1-21. Install a jumper wire with a socket terminal into PA-21.
Remove the wire F716 from P1-22. Install a jumper wire with a socket terminal into P1-22.
Remove the wire E998 from P2-66. Install a jumper wire with a socket terminal into P2-66.
Connect the three jumper wires together.
Turn the battery disconnect switch to the ON position. Expected Result:The status for the Engine Control Switch is Run. The active 336-02 is gone.Results:
OK - The status for the Engine Control Switch is Run. The active 336-02 is gone.Repair: There may be an intermittent problem. If the problem is intermittent, perform the diagnostic functional testTroubleshooting, "Inspecting Electrical Connectors". STOP
Not OK - The status for the Engine Control Switch is "Abnormal/Incorrect Data". The 336-02 code is active.Repair: Replace the ECM. Refer to the diagnostic procedure Troubleshooting, "Replacing the ECM".STOP


Parts protector Suzuki:

09403-14204
 
09403-14204 PROTECTOR, CABLE
DF15, DF15, DF15, DF15S, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF9.9, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH, DT15C, DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCS
61851-93E10
 
61851-93E10 PROTECTOR, SIDE COVER
DF15, DF15, DF15, DF15S, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF8A, DF8AR, DF9.9, DF9.9A, DF9.9AR, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99AR, DF99R, DF99TH
33834-93E00
 
33834-93E00 PROTECTOR
DF15, DF15, DF15S, DF4, DF4, DF46, DF4L, DF6, DF6, DF6L, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
18498-94J20
 
18498-94J20 PROTECTOR (L:320)
DF15, DF15, DF15, DF15A, DF15S, DF20A, DF4, DF4, DF40A, DF40A, DF46, DF4L, DF50A, DF50A, DF6, DF6, DF60A, DF60A, DF6L, DF9.9, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
18498-94J00
 
18498-94J00 PROTECTOR, STARTER CABLE
DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
16919-94J20-280
 
16919-94J20-280 PROTECTOR, BREATHER HOSE
DF15, DF15, DF15, DF15S, DF9.9, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
18498-94J10
 
18498-94J10 PROTECTOR (L:50)
DF15, DF15, DF15S, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
18498-94J31
 
18498-94J31 PROTECTOR (L:390)
DF15, DF15, DF15, DF15S, DF2.5, DF9.9, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH
Back to top