18498-95J00 Suzuki PROTECTOR, BREATHER HOSE


18498-95J00 PROTECTOR, BREATHER HOSE Suzuki DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A PROTECTOR
18498-95J00 PROTECTOR, BREATHER HOSE Suzuki
Rating:
83

Buy PROTECTOR, BREATHER HOSE 18498-95J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

DF70A   DF80A   DF90A   Suzuki

Suzuki entire parts catalog list:

DF70A 2009
DF70A 2010
DF70A 2011
DF80A 2009
DF80A 2010
DF80A 2011
DF90A 2009
DF90A 2010
DF90A 2011

Information:


Illustration 1 g02352096
Illustration 2 g02355179
Table 1
SPECIFICATIONS FOR 342-6646 Piston and Rod    
Callout     Part Number     Part Name     Specification Description    
-     -     -     Apply clean engine oil to the pistons, the piston rings, and the cylinder bore.
Position the piston rings so that the end gaps are located 120 degrees from each other.
Ensure that the proper piston and connecting rod are in the corresponding cylinder with the bearing retainer notch toward the right side of the engine.    
1     160-8197     Bolt     Apply 4C-5593 Thread Lubricant to the threads
Torque to.........................
50 5 N m (37 4 lb ft)
Place an index mark on each bolt.
Torque an additional 90° 5° (1/4 turn).    
4     269-7290     Connecting Rod Bearing     Apply clean engine oil to the upper and lower halves before installation. Endure that the gearing tab comes in contact with the slot in the connecting rod.
Etch the cylinder number on the connecting rod and the cap. Mark the connecting rod and the cap with a number 1 through 6. Mark the numbers on the same side of the connecting rod as the bearing retainer notch.
Install with the part number of the forging for the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block.    
A     -     -     Bore in the connecting rod for the sleeve bearing.......
54.630 0.013 mm (2.1508 0.0005 inch)    
B     -     -     Bore in the bearing for the piston pin.......
50.035 0.008 mm (1.9699 0.0003 inch)    
C     -     -     The connecting rod may be heated from
175 to 260 °C (347 to 500 °F) for the installation of the sleeve bearing. Maximum distance for heating the connecting rod....
85 mm (3.3 inch)
Thoroughly lubricate the piston pin with clean engine oil prior to assembly of the piston and connecting rod.    
D     -     -     The bearing joint must be within 5° of either location.    
E     -     -     Distance between the center of the bearings.......
217 mm (8.5 inch)    
F     -     -     Bore in the connecting rod for the crankshaft bearing.......
85.000 0.013 mm (3.3464 0.0005 inch)    Specifications
Illustration 3 g02352110
Note: Callouts in Table 2 refer to the Assembly Procedure.
Table 2
SPECIFICATIONS FOR 342-6646 Piston and Rod    
Callout     Part Number     Part Name     Specification Description    
4     262-2888
262-2891
300-1319     Piston Ring     Position the spring for the oil control ring in the oil ring groove in the piston body assembly.
Position the oil control ring over the spring. Position the oil control ring so that the gap is 180° from the joint in the spring. Use 4C-3601 Piston Ring Expander to install the oil control ring on the piston.
Use 4C-3601 Piston Ring Expander to install the intermediate piston ring with the side that has the identification "UP-2" toward the top of the piston.
Use 4C-3601 Piston Ring Expander to install the top piston ring with the side that has the identification "UP-1" toward the top of the piston.
Position piston rings (4) so the gaps are 120° from each other.    Removal Procedure
Table 3
Required Tools    
Tool     Part Number     Part Description     Qty    
A     363-4046     Piston Ring Compressor     1    
B     4C-5593     Anti-Seize Compound     1    Start By:
Remove the cylinder head.
Remove the engine oil pump.
Remove the piston cooling jets.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.


Parts protector Suzuki:

18498-99E10
 
18498-99E10 PROTECTOR, FUEL HOSE
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF25, DF25(R)S, DF25Q, DF25Q
18498-87JC0
 
18498-87JC0 PROTECTOR
DF150, DF150, DF150, DF15A, DF175, DF175, DF175, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50,
18498-99EA0
 
18498-99EA0 PROTECTOR (L:80)
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF40A, DF40A, DF50A, DF50A, DF60A, DF60A, DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90, DF90A, DF90A, DF90A
67345-87L00
 
67345-87L00 PROTECTOR
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
67346-87L00
 
67346-87L00 PROTECTOR, HOLDER
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
Back to top