67345-93J00 Suzuki PROTECTOR, R-CON CABLE HOLDER


67345-93J00 PROTECTOR, R-CON CABLE HOLDER Suzuki DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250T, DF250Z PROTECTOR
67345-93J00 PROTECTOR, R-CON CABLE HOLDER Suzuki
Rating:
88

Buy PROTECTOR, R-CON CABLE HOLDER 67345-93J00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Suzuki entire parts catalog list:

DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF200 2011
DF200T 2004,2005,2006,2007
DF200Z 2004,2005,2006,2007
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF225 2011
DF225T 2004,2005,2006,2007
DF225Z 2004,2005,2006,2007
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF250 2011
DF250T 2004,2005,2006,2007
DF250Z 2004,2005,2006,2007

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Mechanical Electronic Injector Unit (MEIU) and Valve Lash Adjustment
Put the number 1 piston at Top Dead Center (TDC) on the compression stroke. Refer to the Testing and Adjusting, Finding Top Center Position No. 1 Piston.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 1 will move freely. If the valves do not move freely, cylinder number 1 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.
Table 1
TDC No. 1 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash C13
0.38 0.08 mm (0.015 0.003 inch) C13
0.76 0.08 mm (0.030 0.003 inch)
Cylinders 1–2–4 1–3–5
Adjust the valve lash using the specifications from Table 1.
Lightly tap the rocker arm with a soft mallet.Note: This tapping ensures that the roller lifter seats against the base circle of the camshaft.
Loosen the adjustment locknut for the appropriate valves.
Place the feeler gauge between the rocker arm and the valve bridge.
Turn the adjustment screw in a clockwise direction while sliding the feeler gauge back and forth between the rocker arm and valve bridge. Continue turning the adjustment screw in a clockwise direction until a slight drag is felt on the feeler gauge.
Tighten the


Parts protector Suzuki:

18498-90J20
PROTECTOR, BREATHER HOSE (590)
18498-90J20 PROTECTOR, BREATHER HOSE (590)
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF25, DF250, DF250, DF250T, DF250Z, DF25Q, DF2
18498-87JC0
 
18498-87JC0 PROTECTOR
DF150, DF150, DF150, DF15A, DF175, DF175, DF175, DF200, DF200, DF200, DF200T, DF200Z, DF20A, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50,
18498-90J00
 
18498-90J00 PROTECTOR, EVAP HOSE
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF25(R)S, DF250, DF250, DF250, DF250T, DF250Z, DF2
18498-93J00
 
18498-93J00 PROTECTOR, FUEL HOSE (L:340)
DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A
34813-93J00
 
34813-93J00 PROTECTOR, LEAD WIRE
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250
56123-93J00
PROTECTOR, OIL SEAL
56123-93J00 PROTECTOR, OIL SEAL
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250T, DF250Z, DF300, DF300
Back to top