32590-92D00 Suzuki REGULATOR BRACKET


32590-92D00 REGULATOR BRACKET Suzuki DT8CENK, DT8CENL, DT8CLJ, DT8CLK, DT8CLL, DT8CLM, DT8CNK, DT8CNL, DT8CSJ, DT8CSL, DT8CSM, DT8MCLN, DT8MCLP, DT8MCLS, DT8MCLT, DT8MCLV, DT8MCSN, DT8MCSP, DT8MCSR, DT8MCSS, DT8MCST, DT8MCSV, DT8MSLR, DT8SCK, DT9.9 CELK, DT9.9CELJ, DT9.9CELL, DT9.9CELM, REGULATOR
32590-92D00 REGULATOR BRACKET Suzuki
Rating:
58

Buy REGULATOR BRACKET 32590-92D00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Suzuki entire parts catalog list:

DT8CENK 1989
DT8CENL 1990
DT8CLJ 1988
DT8CLK 1989
DT8CLL 1990
DT8CLM 1991
DT8CNK 1989
DT8CNL 1990
DT8CSJ 1988
DT8CSL 1990
DT8CSM 1991
DT8MCLN 1992
DT8MCLP 1993
DT8MCLS 1995
DT8MCLT 1996
DT8MCLV 1997
DT8MCSN 1992
DT8MCSP 1993
DT8MCSR 1994
DT8MCSS 1995
DT8MCST 1996
DT8MCSV 1997
DT8MSLR 1994
DT8SCK 1989
DT9.9 CELK 1989
DT9.9CELJ 1988
DT9.9CELL 1990
DT9.9CELM 1991
DT9.9CELN 1992
DT9.9CELP 1993
DT9.9CELR 1994
DT9.9CELS 1995
DT9.9CELT 1996
DT9.9CENK 1989
DT9.9CESJ 1988
DT9.9CESK 1989
DT9.9CESL 1990
DT9.9CESM 1991
DT9.9CESN 1992
DT9.9CESP 1993
DT9.9CESR 1994
DT9.9CESS 1995
DT9.9CEST 1996
DT9.9CNELP 1993
DT9.9CNELR 1994
DT9.9CNELS 1995
DT9.9CNELT 1996
DT9.9CNEXP 1993
DT9.9CNEXR 1994
DT9.9CNEXS 1995
DT9.9CNEXT 1996
DT9.9CNEXV 1997
DT9.9CNJ 1988
DT9.9CNK 1989
DT9.9CNL 1990
DT9.9CNLN 1992
DT9.9MCLJ 1988
DT9.9MCLK 1989
DT9.9MCLL 1990
DT9.9MCLM 1991
DT9.9MCLN 1992
DT9.9MCLP 1993
DT9.9MCLR 1994
DT9.9MCLS 1995
DT9.9MCLT 1996
DT9.9MCLV 1997
DT9.9MCNLR 1994
DT9.9MCNLT 1996
DT9.9MCNLV 1997
DT9.9MCSJ 1988
DT9.9MCSK 1989
DT9.9MCSL 1990
DT9.9MCSM 1991
DT9.9MCSN 1992
DT9.9MCSP 1993
DT9.9MCSR 1994
DT9.9MCSS 1995
DT9.9MCST 1996
DT9.9MCSV 1997

Information:


Illustration 1 g06341337
Table 1
Specifications for 7E-8758 Cylinder Head Gp, 203-2169 Cylinder Head Gp, 203-2170 Cylinder Head Gp, 242-5326 Cylinder Head As and 350-5202 Cylinder Head Gp
Item Qty Part Specification Description
1 2 130-2607 Valve Seat Insert During installation, shrink the valve seat insert with reduced temperature (Reference temperature: −60° C (−76° F)) and press the insert into the cylinder head counterbore.
2 2 130-2608 Valve Seat Insert During installation, shrink the valve seat insert with reduced temperature (Reference temperature: −60° C (−76° F)) and press the insert into the cylinder head counterbore.
3 5 3B-0645 Cup Plug Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores.
4 1 3B-0623 Cup Plug Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores.
5 2 3B-0623 Cup Plug Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. Installation depth (E) is 1.0 0.5 mm (0.04 0.02 inch)
6 2 3B-0623 Cup Plug Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. Installation depth (D) is 9.0 0.5 mm (0.35 0.02 inch)
Illustration 2 g06341342
Table 2
Bolt Tightening Procedure with the 110-6991 Cylinder Head Gasket
Item Qty Part Specification Description
Note: Bolt Tightening Procedure with the 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).
7 6
131-0420 Cylinder Head Fastener Gp
Use the following procedure in order to tighten the bolts for the cylinder head: Refer to Illustration 2 for bolt tightening sequence.
1. Before assembly, apply clean engine oil to the bolt threads.
2. Tighten bolt 1 through 8 in the numerical sequence to 30 5 N m (22 4 lb ft).
3. Again, retighten bolts 1 through 8 in the numerical sequence to 200 15 N m (148 11 lb ft).
4. Again, retighten bolts 1 through 8 in numerical sequence to 200 15 N m (148 11 lb ft).
5. Turn bolt 1 through 8 in numerical sequence to an angle of 180 5 degrees.
Note: Tighten bolts 9 only after bolts 1 through 8 have been turned 180 5 degrees.
6. Tighten bolts (9) to 55 10 N m (41 7 lb ft).
8 2
131-0421 Cylinder Head Fastener Gp
9 2
5B-0213 Bolt
Illustration 3 g06341366
Table 3
Bolt Tightening Procedure with the 362-8264 Cylinder Head Gasket
Item Qty Part Specification Description
Note: Bolt Tightening Procedure with the 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).
Note: Refer to Disassembly and assembly manual for the alternate tightening procedure of cylinder head using 362-8264 Cylinder Head Gasket (MLS) with 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).
7 6
131-0420 Cylinder Head Fastener Gp
Use the following procedure in order to tighten the bolts for the cylinder head: Refer to Illustration 3 for bolt tightening sequence.
1. Before assembly, apply clean engine oil to the bolt threads.
2. Tighten bolt 1 through 8 in the numerical sequence to 30 5 N m (22 4 lb ft).
3. Again, retighten bolts 1 through 8 in the numerical sequence to 145 15 N m (107 11 lb ft).
4. Again, retighten bolts 1 through 8 in the numerical sequence to 145 15 N m (107 11 lb ft).
5. Turn bolts 1 through 8 in the numerical sequence to an angle of 180 5 degrees.
Note: Tighten bolts 9 only after bolts 1 through 8 have been given the final torque.
7. Tighten bolts 9 to 55 10 N m (40 7 lb ft).
8 2
131-0421 Cylinder Head Fastener Gp
9 2
5B-0213 Bolt


Parts regulator Suzuki:

32500-95722
 
32500-95722 Regulator, voltage
DT15C, DT15ELG, DT15ELH, DT15ELJ, DT15ESG, DT15ESH, DT15ESJ, DT15MLG, DT15MLH, DT15MLJ, DT15MSG, DT15MSH, DT15MSJ, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLG, DT25MLH, DT25MLJ, DT25MSG, DT25MSH, DT25MSJ, DT4, DT40C, DT50ECLE, DT50M
32501-92D00
 
32501-92D00 REGULATOR SET
DT8CENK, DT8CENL, DT8CLJ, DT8CLK, DT8CLL, DT8CLM, DT8CNK, DT8CNL, DT8CSJ, DT8CSL, DT8CSM, DT8MCLN, DT8MCLP, DT8MCLS, DT8MCLT, DT8MCLV, DT8MCSN, DT8MCSP, DT8MCSR, DT8MCSS, DT8MCST, DT8MCSV, DT8MSLR, DT8SCK, DT9.9 CELK, DT9.9CELJ, DT9.9CELL, DT9.9CELM,
Back to top