31800-95241 Suzuki Relay Assembly


31800-95241 Relay Assembly Suzuki 20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M Relay
31800-95241 Relay Assembly Suzuki
Rating:
93

Buy Relay Assembly 31800-95241 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Suzuki entire parts catalog list:

20ELB 1977
20ELC 1978
20ELN 1979
25ELB 1977
25ELC 1978
25ELN 1979
25ELT 1980
25ELX 1981
DT20ESB 1977
DT20ESC 1978
DT20ESN 1979
DT20MLB 1977
DT20MLC 1978
DT20MLN 1979
DT20MSB 1977
DT20MSC 1978
DT20MSN 1979
DT25ELZ 1982
DT25ESB 1977
DT25ESC 1978
DT25ESN 1979
DT25EST 1980
DT25ESX 1981
DT25ESZ 1982
DT25MLB 1977
DT25MLC 1978
DT25MLN 1979
DT25MLT 1980
DT25MLX 1981
DT25MLZ 1982
DT25MSB 1977
DT25MSC 1978
DT25MSN 1979
DT25MST 1980
DT25MSX 1981
DT25MSZ 1982
DT28F 1979
DT28G 1980
DT28J 1981
DT28Z 1982
DT35ELT 1980
DT35ELX 1981
DT35ELZ 1982
DT35EST 1980
DT35ESX 1981
DT35ESZ 1982
DT35MLT 1980
DT35MLX 1981
DT35MLZ 1982
DT35MST 1980
DT35MSX 1981
DT35MSZ 1982
DT40ELT 1980
DT40ELX 1981
DT40ELZ 1982
DT40EST 1980
DT40ESX 1981
DT40ESZ 1982
DT40MLT 1980
DT40MLX 1981
DT40MLZ 1982
DT40MSX 1981
DT40MSZ 1982
DT50 1980,1981,1982
DT50 1983
DT50M 1980,1981,1982
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9S-9082     Engine Turning Tool     1    
B (1)     5P-3526     Piston Ring Compressor     1    
B (2)     200-3914     Piston Ring Compressor     1    
C     8T-3052     Degree Wheel     1    
( 1 ) For use with the C15 engine.
( 2 ) For use with the C18 engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston.Note: The piston and connecting rod are matched to a specific cylinder. Ensure that the connecting rod and pistons are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 1 g01048560
Note: Be careful not to damage the cylinder liner, the crankshaft journal during installation of the piston and the connecting rod.
Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner.Note: Install the connecting rod so that the bearing tab is located on the side of the piston cooling jet.
Install the upper connecting rod bearing in the connecting rod.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Lubricate the connecting rod bearing with clean engine oil and pull the connecting rod onto the crankshaft journal.
Install the lower connecting rod bearing in the connecting rod bearing cap.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Illustration 2 g01016640
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil and install bolts (1) .
Tighten bolts (1), as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (A) and Bolt (C) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".


Parts relay Suzuki:

31100-95242
RELAY ASSY
31100-95242 RELAY ASSY
DT50, DT50, DT50M, DT50W, DT65, DT65
31800-95240
 
31800-95240 Relay Assembly
25ELT, 25ELX, DT25ELZ, DT25EST, DT25ESX, DT25ESZ, DT25MLT, DT25MLX, DT25MLZ, DT25MST, DT25MSX, DT25MSZ, DT28G, DT28J, DT28Z
Back to top