09390-40003 Suzuki Ring, Thrust


09390-40003 Ring, Thrust Suzuki DT2B, DT2C, DT2D, DT2E, DT2F, DT2N, DT2T, DT2X, DT2Z Ring
09390-40003 Ring, Thrust Suzuki
Rating:
63

Buy Ring, Thrust 09390-40003 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Suzuki entire parts catalog list:

DT2B 1977
DT2C 1978
DT2D 1983
DT2E 1984
DT2F 1985
DT2N 1979
DT2T 1980
DT2X 1981
DT2Z 1982

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01344541
Typical example
Place a suitable container below the engine oil pan. Remove drain plug (5) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Illustration 2 g01251767
Typical example
Remove O-ring seal (11) from drain plug (5).
Disconnect breather hose (1) from clip (6). Position the breather hose away from the engine oil pan.
If necessary, remove the assembly of dipstick tube. Loosen nut (3) and remove tube assembly (2). Remove seal (4) from the tube assembly. Note: Identify the position and orientation of the tube assembly.
Support the assembly of the engine oil pan. Mark the position of clip (6). Loosen the bolt that secures the clip and remove the clip.
Remove bolts (9) and (10).
Remove engine oil pan (8) and remove joint (7) from the cylinder block. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 100 mm) 4
B - Loctite 5900 -
C - Loctite 5188 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surface of the cylinder block is clean and free from damage.
Illustration 3 g01251768
Typical example
Install Tooling (A) to positions (X) in the cylinder block.
Ensure that the engine oil pan is clean and free from damage.
Illustration 4 g01251763
Typical example
Illustration 5 g01251766
Typical example
Apply a bead of Tooling (B) to positions (Y) on the cylinder block. Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (B) has cured.
Illustration 6 g01251767
Typical example
Position a new joint (7) onto engine oil pan (8).
Illustration 7 g01344541
Typical example
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the cylinder block.
Install bolts (9) finger tight. Install clip (6) in the correct position.
Remove Tooling (A).
Apply Tooling (C) to bolts (10). Install bolts (10) and remaining bolts (9).
Tighten bolts (9) and (10) to a torque of 22 N m (16 lb ft).
Install a new O-ring seal (11) to drain plug (5). Install the drain plug to engine oil pan (8). Tighten the oil drain plug to a torque of 34 N m (25 lb ft).
If necessary, follow Steps 12.a through 12.c in order to install the assembly of the dipstick tube.
Install a new seal (4) to tube assembly (2).
Apply Tooling (C) to nut (3). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten nut (3) to a torque of 18 N m (13 lb ft). Install the dipstick.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the procedure.


Parts ring Suzuki:

13432-33110
Ring, Friction
13432-33110 Ring, Friction
DT2.2SV, DT25C, DT2B, DT2C, DT2D, DT2E, DT2F, DT2LG, DT2LH, DT2LJ, DT2LK, DT2LL, DT2N, DT2SG, DT2SH, DT2SJ, DT2SK, DT2SL, DT2SM, DT2SN, DT2SP, DT2SR, DT2SS, DT2ST, DT2T, DT2X, DT2Z, DT30C, DT30CRLJ, DT30CRSJ, DT30MCLJ, DT30MCSJ, DT40C
09380-07001
 
09380-07001 Ring, Clamp Plate
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16SB, DT16SC, DT16SN, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ESB, DT25ESC, DT25ESN, DT25MLB, DT25MLC, DT25MLN, DT25
12141-35010
 
12141-35010 Ring, Piston
DT2B, DT2C, DT2N
12141-35010-025
 
12141-35010-025 Ring, Piston
DT2B, DT2C, DT2N
12141-35010-050
 
12141-35010-050 Ring, Piston
DT2B, DT2C, DT2N
12140-98400
Ring Set, Piston
12140-98400 Ring Set, Piston
DT2.2SV, DT2B, DT2C, DT2D, DT2E, DT2F, DT2LG, DT2LH, DT2LJ, DT2LK, DT2LL, DT2N, DT2SG, DT2SH, DT2SJ, DT2SK, DT2SL, DT2SM, DT2SN, DT2SP, DT2SR, DT2SS, DT2ST, DT2T, DT2X, DT2Z
12140-98401-025
 
12140-98401-025 Ring Set, Piston
DT2B, DT2C, DT2D, DT2E, DT2F, DT2N, DT2T, DT2X, DT2Z
12140-98401-050
 
12140-98401-050 Ring Set, Piston
DT2B, DT2C, DT2D, DT2E, DT2F, DT2N, DT2T, DT2X, DT2Z
Back to top