25111-93510 Suzuki Rod, Shifting


25111-93510 Rod, Shifting Suzuki DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ Rod
25111-93510 Rod, Shifting Suzuki
Rating:
73

Buy Rod, Shifting 25111-93510 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 36-1
 

Suzuki entire parts catalog list:

DT16LT 1980
DT16LT 1981
DT16LT 1982
DT16ST 1980
DT16ST 1981
DT16ST 1982
DT9.9LT 1980
DT9.9LX 1981
DT9.9LZ 1982
DT9.9ST 1980
DT9.9SX 1981
DT9.9SZ 1982

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
C FT-2398 Oil Pump Shaft Tool 1
0S-1627 Bolts 2
2J-3506 Full Nuts 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01209057Note: On the lower bearing, align the hole in the bearing with the hole in the oil pump's body.
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press in order to install bearings (11) into pump body (9). Install the bearings 12.30 0.25 mm (0.484 0.010 inch) below the surface of pump body (9). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 2 g01209062
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press in order to install bearings (7) into cover (6). Align the hole in the bearing with the hole in the cover. Install the bearings 7.50 0.25 mm (0.230 0.010 inch) below the surface of cover (6). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 3 g01209063
Ensure that dowels (14) are installed to a height of 12.0 1.0 mm (0.47 0.04 inch).
Place O-ring seal (12) and O-ring seals (13) in position on cover (6). Apply clean engine oil to the O-ring seals.
Apply a coat of clean engine oil to the bearings and the gear pockets in pump body (9).
Place drive shaft (8) and idler shaft (10) in pump body (9). Ensure that the gears are 0.14 to 0.16 mm (0.006 to 0.010 inch) below the surface of the pump body.
Apply clean engine oil to the bearings in cover (6). Apply clean engine oil to the top surface of the gears in pump body (9).
Place cover (6) in position on pump body (9).
Illustration 4 g01209072
Ensure that cover (6) is against the pump body. Ensure that all of the O-ring seals are in place. Install the bolts that hold cover (6) to the pump body.
Ensure that plug (15) is installed in the idler shaft.
Ensure that plug (16) is installed in the cover.
Illustration 5 g01209075
Illustration 6 g00628384Note: Ensure that dowel (17) is installed at the location that is shown in Illustration 5 for a SAE standard rotation engine.
Install dowel (17) to a height of 8.0 1.0 mm (0.32 0.04 inch).
Ensure that plugs (18) are installed.
Use Tooling (C) in order to install gear (5) and the washer. Install bolt (4).
Strike the head of the bolt with a hammer. Tighten the bolt again.
Install drive gear (3).
Illustration 7 g01209076
Ensure that plug (19) is installed in the drive shaft.
Ensure that hollow dowel (20) is installed to a height of 4.0 0.5 mm (0.16 0.02 inch).
Place the O-ring seal on the dowel. Apply a coat of clean engine oil to the O-ring seal.
Install the O-ring seals on cover (1) and cover (2). Apply a coat of clean engine oil to the O-ring seals.
Install cover (1) and cover (2).
Rotate the pump by hand. The pump must rotate freely. If the pump does not rotate freely, disassemble the pump in order to determine the cause. End By:
Install the engine oil pump.


Parts rod Suzuki:

57631-93100
 
57631-93100 Rod, Push
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT7.5LB, DT7.5LC, DT7.5LN, DT7.5SB, DT7.5SC, DT7.5SN, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ, DT9C, DT9D, DT9F
23111-93100
 
23111-93100 Rod, Clutch
DT14C, DT14D, DT14F, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
25111-93100
 
25111-93100 Rod, Shifting
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
25111-93750
 
25111-93750 Rod, Shifting
DT14C, DT14D, DT14F, DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
25111-93760
 
25111-93760 Rod, Shifting
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
12161-23000
Rod, Connecting
12161-23000 Rod, Connecting
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
21312-93100
 
21312-93100 Rod, Inter Lock
DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
63221-93200
 
63221-93200 Rod, Handle
DT14F, DT16LN, DT16LT, DT16LT, DT16LT, DT16SN, DT16ST, DT16ST, DT16ST, DT5LT, DT5LX, DT5LZ, DT5ST, DT5SX, DT5SZ, DT8LT, DT8LX, DT8LZ, DT8ST, DT8SX, DT8SZ, DT9.9LT, DT9.9LX, DT9.9LZ, DT9.9ST, DT9.9SX, DT9.9SZ
Back to top