32100-95204 Suzuki ROTOR


32100-95204 ROTOR Suzuki DT50, DT50M, DT50W, DT65, DT65 ROTOR
32100-95204 ROTOR Suzuki
Rating:
28

Buy ROTOR 32100-95204 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50M 1980,1981,1982
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982

Information:

This procedure checks for air in the fuel system. This procedure also assists in finding the source of the air.
Examine the fuel system for leaks. Ensure that the fuel line fittings are properly tightened. Check the fuel level in the fuel tank. Air can enter the fuel system on the suction side between the fuel transfer pump and the fuel tank.
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Install a 2P-8278 Fuel Flow Tube (Sight Gauge) in the fuel return line. When possible, install the sight gauge in a straight section of the fuel line that is at least 304.8 mm (12 inches) long. Do not install the sight gauge near the following devices that create turbulence:
Elbows
Relief valves
Check valvesObserve the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel that is present in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds. When possible, operate the engine under the conditions which have been suspect.
Illustration 1 g00578151
2P-8278 Fuel Flow Tube (Sight Gauge)
(1) A steady stream of small bubbles with a diameter of approximately 1.60 mm (0.063 inch) is an acceptable amount of air in the fuel.
(2) Bubbles with a diameter of approximately 6.35 mm (0.250 inch) are also acceptable if there are 2 second to 3 second intervals between bubbles.
(3) Excessive air bubbles in the fuel are not acceptable.
If excessive air is seen in the sight gauge in the fuel return line, install a second sight gauge at the inlet to the fuel transfer pump. If a second sight gauge is not available, move the sight gauge from the fuel return line and install the sight gauge at the inlet to the fuel transfer pump. Observe the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel that is present in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds. If excessive air is not seen at the inlet to the fuel transfer pump, the air is entering the system after the fuel transfer pump. Refer to the Testing and Adjusting, "Fuel System - Prime".If excessive air is seen at the inlet to the fuel transfer pump, air is entering through the suction side of the fuel system.
To avoid personal injury, always wear eye and face protection when using pressurized air.
To avoid damage, do not use more than 55 kPa (8 psi) to pressurize the fuel tank.
Pressurize the fuel tank to 35 kPa (5 psi). Do not use more than 55 kPa (8 psi) in order to avoid damage to the fuel tank. Check for leaks in the fuel lines between the fuel tank and the fuel transfer pump. Repair any leaks that are found. Check the fuel pressure in order to ensure that the fuel transfer pump is operating properly. For information about checking the fuel pressure, see Testing and Adjusting, "Fuel System Pressure - Test".
Ensure that the fuel transfer pump is operating correctly. Refer to Testing and Adjusting, "Fuel System Pressure - Test".


Parts rotor Suzuki:

32100-95301
 
32100-95301 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32102-95300
 
32102-95300 ROTOR (MODEL G)
DT50, DT50M, DT50W, DT65, DT65
32102-95301
 
32102-95301 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32102-95202
 
32102-95202 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32102-95220
 
32102-95220 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32100-95331
 
32100-95331 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32102-95332
 
32102-95332 ROTOR
DT50, DT50M, DT50W, DT65, DT65
32102-95331
 
32102-95331 ROTOR (MODEL G)
DT50, DT50M, DT50W, DT65, DT65
Back to top