61112-93J20 Suzuki RUBBER, ENG COVER


61112-93J20 RUBBER, ENG COVER Suzuki DF200, DF225, DF250 RUBBER
61112-93J20 RUBBER, ENG COVER Suzuki
Rating:
73

Buy RUBBER, ENG COVER 61112-93J20 Suzuki genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$129.09
 

19-09-2023

-: -
Suzuki Outboard Engine Cowling Cover Seal Df200/225/250 - Suzuki OEM Engine Cover Rubber Part Number# 61112-93J20
Engine Cowling Cover Seal || 100% OEM Original Part || Seal That Goes Around The Base Of The Engine Cover To Seal The Water Out || FITS: SUZUKI DF200/225/250 MODELS 2004-2016
Number on catalog scheme: 2
 

Compatible models:

DF200   DF225   DF250   Suzuki

Suzuki entire parts catalog list:

DF200 2011
DF225 2011
DF250 2011

Information:

Start By:a. remove sea water pump1. Drain the coolant from the cooling system.2. Remove three bolts located under the sea water pump connecting auxiliary pump to the front housing. 3. Remove four bolts, two flanges, one clamp and remove pipe (1). Remove four bolts two flanges and pipe (2). For clarity purposes, the heat exchanger has been removed. The heat exchanger does not have to be removed to remove the auxiliary pump. 4. Remove two bolts, two flanges, (5) one clamp and one connector and pivot pipe (6) away from adapter (3).5. Remove four long bolts (4) and remove adapter (3) from the auxiliary pump. 6. Fasten a hoist to pump (8) with tooling (A) as shown. Remove six bolts (7) that hold pump (8) in position. Pull the pump and drive gear out of the front housing, and remove the unit from the engine. The weight of the unit is 39 kg (86 lb.). Installation of the auxiliary pump is accomplished in the exact reverse order from removal.7. After the inlet and outlet water lines have been connected, fill the cooling system with coolant to the correct level. See the Maintenance Manual for the correct fluid level.End By:a. install sea water pumpDisassemble Auxiliary Pump (Fresh Water)
Start By:a. remove auxiliary pump (fresh water) 1. Remove O-ring seals (3) and (4) from the pump housing.2. Remove the bolts and gear (2) from shaft (1). 3. Remove the bolts and adapter (5) from the pump housing. Remove the O-ring seal from adapter (5). 4. Loosen bolt (6) and the washer that hold impeller (7) to the shaft.5. Use tooling (A) to loosen impeller (7) from the end of the pump shaft. Remove tooling (A), bolt (6), the washer and impeller (7) from the pump shaft and housing. 6. Remove spring (9) from carbon seal assembly (10). Remove carbon seal assembly (10) from the end of shaft (8). 7. Remove the bolts that hold retainer washers (12) to the pump housing. Remove shaft (1) and washers (12) from the pump housing. 8. Remove the bolts that hold the shims and retainer washers (13) to the pump housing. Remove shaft (8), the shims and washers (13) from the pump housing.9. Remove the rubber ring and ceramic seal (11) from the pump housing. See illustration B24522P1. 10. Remove lip-type seal (14) from the pump housing. 11. Remove bearing (15) from the pump housing.Assemble Auxiliary Pump (Fresh Water)
1. Make sure the oil hole in the bearing is in alignment with the oil passage in housing (1). Use tool group (A) and a press to push the bearing in housing (1) until it is 1.5 0.5 mm (.06 .02 in.) below the surface of housing (1). The inside diameter of the bearing must be 75.000 0.055 mm (2.9528 .0022 in.). 2. Use tool group (A) to install the lip-type seal in housing (1). Make sure the lip of the seal is toward the bearing as shown. Put clean engine oil on the lip of the seal. 3. Install shaft (2) in the pump housing. Install retainer washers (3), the shims and bolts to hold shaft (2) in the pump housing. 4. Put clean engine oil on the bearing in the pump housing, and install shaft (4) and retainer washers (5) over shaft (2). Install the bolts to hold retainer washers (5) to the pump housing.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Install ceramic seal ring (6) in the rubber seal. Put clean water on the rubber seal and ceramic seal ring for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to install the seal and seal ring as shown. 6. Remove the spring from carbon seal assembly (7). Put clean water on the inside diameter of the seal assembly for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to push seal assembly (7) on the shaft until seal faces make light contact. 7. Install spring (8) on carbon seal assembly (7). 8. Put impeller (9) in position on the pump shaft as shown. 9. Install the bolt and washer that hold impeller (9) to the pump shaft. Tighten the bolt to a torque of 38 4 N m (28 3 lb ft). 10. Install O-ring seal (11) around adapter (10), and put a small amount of engine oil or glyceride on it.11. Put adapter (10) in position, and install the bolts to hold it to the pump housing. 12. Put gear (12) in position on shaft (4), and install the bolts to hold gear (12). 13. Install O-ring seals (13) and (14) in the pump housing, and put clean engine oil on the O-ring seals.End By:a. install auxiliary pump (fresh water)


Parts rubber Suzuki:

55332-98J00
 
55332-98J00 RUBBER, EXHAUST SEAL
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DF250A, DF300, DF300, DF300A
Back to top