41211-94301 Suzuki SCREW


41211-94301 SCREW Suzuki DT40, DT50 SCREW
41211-94301 SCREW Suzuki
Rating:
73

Buy SCREW 41211-94301 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

DT40   DT50   Suzuki

Suzuki entire parts catalog list:

DT40 1983
DT50 1983

Information:

Note: Refer to Systems Operation, Testing, and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the engine is stopped before any servicing or repair is performed.
Fuel System Primary Filter (Water Separator) Element for Electric Fuel Priming Pump
Remove the Element
Turn the fuel supply valve (if equipped) to the OFF position before performing this maintenance.
Place a suitable container under the water separator to catch any fuel that might spill. Clean up any spilled fuel. Clean the outside body of the filter assembly.
Illustration 1 g06304505
Typical example
Install a suitable tube onto drain (2). Open the drain valve (1). Rotate the drain valve fully counterclockwise. Two full turns are required.
Allow the fuel to drain into the container.
Remove the tube from the drain (2).
Remove the wiring harness from connection (3).
Rotate filter bowl (5) counterclockwise and remove the filter bowl from assembly.Note: If a strap wrench is required to loosen the filter bowl (5), ensure that the strap is positioned in the middle of the ribbed section. To avoid damage or mechanical failure, do not position the strap around the clear area. Do not apply loads to the clear plastic bowl and the joint of the black plastic section of the lower bowl.
Illustration 2 g06304508
Typical example
Remove the filter element (4). Clean the filter bowl.Install the New Filter Element
Illustration 3 g06304524
Typical example
After repositioning the self-venting drain up, locate the thread in the new filter element (6) onto the thread (7). Spin on the filter element and tighten the drain valve (2) securely.
Lubricate the lip (Position (X)) with clean engine oil. Do NOT fill the bowl with fuel before the assembly is installed.Note: Do not use a tool to install the filter assembly.
Align the filter bowl (5) to the assembly. Rotate the filter bowl (5) clockwise by hand. Rotate the filter bowl (5) until there is no visible gap between the element and the filter bowl and the assembly.
Remove the container and dispose of the fuel in a safe place.
Install the wiring harness to connection (3).
The secondary filter element (if equipped) must be replaced at the same time as the primary filter element. Refer to the Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace".Fuel System Primary Filter (Water Separator) Element for Manual Fuel Priming Pump
Remove the Element
Turn the fuel supply valve (if equipped) to the OFF position before performing this maintenance.
Place a suitable container under the water separator to catch any fuel that might spill. Clean up any spilled fuel. Clean the outside body of the filter assembly.
Illustration 4 g06398147
Typical example
Install a suitable tube onto drain (2). Open the drain valve (1). Rotate the drain valve fully counterclockwise. Two full turns are required.
Allow the fuel to drain into the container.
Remove the tube from the drain (2).
Remove the wiring harness from connection (3).
Rotate filter bowl (5) counterclockwise and remove the filter bowl from assembly.Note: If a strap wrench is required to loosen the filter bowl (5), ensure that the strap is positioned in the middle of the ribbed section. To avoid damage or mechanical failure, do not position the strap around the clear area. Do not apply loads to the clear plastic bowl and the joint of the black plastic section of the lower bowl.
Illustration 5 g06398170
Typical example
Remove the filter element (4). Clean the filter bowl.Install the New Filter Element
Illustration 6 g06304524
Typical example
After repositioning the self-venting drain up, locate the thread in the new filter element (6) onto the thread (7). Spin on the filter element and tighten the drain valve (2) securely.
Lubricate the lip (Position (X)) with clean engine oil. Do NOT fill the bowl with fuel before the assembly is installed.Note: Do not use a tool to install the filter assembly.
Align the filter bowl (5) to the assembly. Rotate the filter bowl (5) clockwise by hand. Rotate the filter bowl (5) until there is no visible gap between the element and the filter bowl and the assembly.
Remove the container and dispose of the fuel in a safe place.
Install the wiring harness to connection (3).
The secondary filter element (if equipped) must be replaced at the same time as the primary filter element. Refer to the Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace".


Parts screw Suzuki:

02122-06168
 
02122-06168 Screw
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT
02112-03068
 
02112-03068 Screw
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT14C, DT14D, DT14F, DT15ELG, DT15ELH, DT15ELJ, DT15ESG, DT15ESH, DT15ESJ, DT15MLG, DT15MLH, DT15MLJ, DT15MSG, DT15MSH, DT15MSJ, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16
02112-05358
Screw
02112-05358 Screw
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M
13269-95210
 
13269-95210 Screw, pilot air
DT115, DT140, DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT35TCLH
02112-06088
 
02112-06088 Screw
DT50, DT50, DT50ECLE, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MCLE, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT5LC, DT5LN, DT5LT, DT5SC, DT5SN, DT5ST, DT60CLE, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN, DT8LT, DT8LX, D
13267-95211
 
13267-95211 Screw, throttle stop
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT50, DT50, DT50M, DT50W, DT60CLD, DT
02112-06458
 
02112-06458 Screw
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ
02142-05208
Back to top