61113-96300 Suzuki Seal, under cover

Table 1
Warning Category Indicator (WCI) (1), (2), and (3)
WCI Severity
(1) Least Severe
(2) Moderate Severity
(3) Most Severe Use Caterpillar Electronic Technician (ET) to perform the following activities for the monitoring system:
Viewing parameters
Parameter programming
Set delay timesThe default settings for the parameters are programmed at the factory. To accommodate unique applications and sites, some of the parameters may be reprogrammed with Cat ET. Use Cat ET to modify the monitoring system parameters.Note: Some parameters do not require a password in order to be changed. Other parameters can be changed with customer passwords. Some of the parameters are protected by factory passwords. Some parameters cannot be changed. Some applications do not allow any changes to the programmable monitoring system. Parameters that are protected by factory passwords can only be changed by dealer personnel.Viewing or Changing the Settings of the Monitoring System
Print a "Product Status Report" for your engine prior to continuing. The report will provide a reference to the current state of the engine.Use the following procedure in order to view the parameter settings and/or change the parameter settings:
Select the "Service/Monitoring System" screen on Cat ET. Note: Ensure that you select the correct ECM for the parameters that are being changed before continuing.
Highlight the desired parameter. Select the "Change" button in the lower left corner of the screen. The "Change Monitor System" screen will appear.
Change the "State" of the parameter.
Set the "Trip Point" and the "Delay Time" according to the "Allowed Values" that are displayed in the lower half of the screen.
Click the "OK" button. If a password is required, the "Enter Passwords" screen will appear. Enter the correct passwords and then click the "OK" button. The new settings will be effective immediately.Note: If a factory password is required, the "Enter Factory Passwords" screen will appear. Refer to Troubleshooting, "Factory Passwords".Note: Factory passwords are only available to service technicians from an authorized Caterpillar Dealership. Customers of Caterpillar do not have access to the Caterpillar Feature Protection System (FPS).Trip Points for the Engine Monitoring System
The ECM monitors the operating parameters of the engine. The ECM can generate a code for specific parameters that exceed an acceptable range. The acceptable range for each parameter is defined by the setpoints that are programmed into the ECM. Some of the setpoints for the parameters may be programmable by the technician. Access the engine monitoring system on Cat ET in order to view the current parameter settings.Table 2 contains the codes that can be generated by the ECM. Most of the codes will coincide with a parameter that is monitored by the engine monitoring system. Some of the codes may be generated from a switched input or generated from calculated values that are based on multiple sensor inputs. These types of codes would not coincide with a parameter that is monitored by the engine monitoring system. Table 2 also contains the default settings for each parameter.
Table 2
Monitoring System Parameters
J1939 Code and Description WCI Default Delay Time in Seconds Default Trip Point Default State
95-15 Engine Fuel Filter Differential Pressure : High - least severe (1) 0 Pressure differential switch is tripped. Always On
100-1 Engine Oil Pressure : Low - most severe (3) 4 Refer to Table 4 for details. Always On
100-17 Engine Oil Pressure : Low - least severe (1) 8 Refer to Table 3 for details. Always On
100-18 Engine Oil Pressure : Low - moderate severity (2) Not Available Not Available Not Available
101-15 Engine Crankcase Pressure : High - least severe (1) Not Available Not Available Not Available
101-16 Engine Crankcase Pressure : High - moderate severity (2) Not Available Not Available Not Available
102-18 Engine Intake Manifold #1 Pressure : Low - moderate severity (2) Not Available Not Available Not Available
105-0 Engine Intake Manifold #1 Temperature : High - most severe (3) Not Available Not Available Not Available
105-15 Engine Intake Manifold #1 Temperature : High - least severe (1) 4 115° C (239° F) Always On
105-16 Engine Intake Manifold #1 Temperature : High - moderate severity (2) 4 120° C (248° F) Off
110-0 Engine Coolant Temperature : High - most severe (3) 10 111° C (228° F) Off
110-15 Engine Coolant Temperature : High - least severe (1) 10 110° C (230° F) Always On
110-16 Engine Coolant Temperature : High - moderate severity (2) 10 111° C (228° F) Off
111-1 Engine Coolant Level : Low - most severe (3) 10 None Off
111-17 Engine Coolant Level : Low - least severe (1) 10 None On
111-18 Engine Coolant Level : Low - moderate severity (2) Not Available Not Availa