61134-88L00 Suzuki SEAL, SIDE COVER


61134-88L00 SEAL, SIDE COVER Suzuki DF40A, DF40A, DF50A, DF50A, DF60A, DF60A SEAL
61134-88L00 SEAL, SIDE COVER Suzuki
Rating:
88

Buy SEAL, SIDE COVER 61134-88L00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

DF40A   DF50A   DF60A   Suzuki

Suzuki entire parts catalog list:

DF40A 2010
DF40A 2011
DF50A 2010
DF50A 2011
DF60A 2010
DF60A 2011

Information:


Table 1
Required Tools
Tool Part Number Part Name Qty
A
(1) 208-0888 Engine Turning Tool 1
B
(2) 5P-7305 Engine Turning Tool 1
5P-7306 Shaft Housing 1
C
(3) 350-7549 Engine Turning Tool 1
D 136-4632 Timing Pin 1
208-9388 Adapter 1
208-9387 Timing Pin Optional Longer Pin 1
E 294-3031 Fuel Pump Pinch Bolt 1
(1) The tooling is designed to turn the crankshaft in engines that are equipped with rear PTO. The tool engages the forward spline of upper gear of the PTO.
(2) The tooling is designed to turn the crankshaft in engines that are equipped with standard electric starters.
(3) The tooling is designed to turn the crankshaft in engines that have limited access to the flywheel housing. The tool engages all four bolt heads which are located in the front vibration damper.Note: Cleanliness is a critical factor. Clean the exterior of the components before you begin the removal procedure. This action will help to prevent dirt from entering the internal mechanism.Note: Do not remove the valve mechanism cover at any time during this procedure.
Illustration 1 g02112896
Flywheel housing
Illustration 2 g02112894
Remove plug (X) from the timing hole that is located in the flywheel housing. Install the assembled timing pin (D) into the timing hole.
Use Tooling (A) and (B) in order to rotate the flywheel. Turn the flywheel in the direction of engine rotation. The direction of engine rotation is clockwise, as the engine is viewed from the vibration damper. Turn the vibration damper and the flywheel until the timing pin engages with the threaded hole in the flywheel. Note: If the flywheel is turned beyond the point of engagement, the flywheel must be turned in the direction that is reverse of normal engine rotation. Turn the flywheel by approximately 30 degrees. Then turn the flywheel in the direction of normal rotation until the timing pin engages with the threaded hole.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Remove all necessary components in order to access the fuel injection pump.
Illustration 3 g02351981
Remove plug (1) and remove O-ring seal (2).
Illustration 4 g02351995
Install Tooling (E). Tighten Tooling (E) to a torque of 9 1 N m (80 9 lb in). Note: The pump will not function while Tooling (E) is installed. Running the fuel injection pump with the tooling installed will result in pump damage and system contamination.


Parts seal Suzuki:

33799-97E00
 
33799-97E00 SEAL, OIL
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF2
09289-05012
 
09289-05012 SEAL, OIL
DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF25, DF25(R)S, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF25Q, DF25Q
12281-87J00
SEAL, OIL
12281-87J00 SEAL, OIL
DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50A, DF50QH, DF50TL, DF60A, DF60A, DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
16519-87L00
 
16519-87L00 SEAL, ENGINE HOLDER
DF40A, DF40A, DF50A, DF50A, DF60A, DF60A, DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
09283-37005
SEAL, UPPER OIL (36.5X49X6)
09283-37005 SEAL, UPPER OIL (36.5X49X6)
DF40A, DF40A, DF50A, DF50A, DF60A, DF60A
61438-88L00
 
61438-88L00 SEAL, TILT UP HANDLE NO.1
DF40A, DF40A, DF50A, DF50A, DF60A, DF60A
61439-88L00
 
61439-88L00 SEAL, TILT UP HANDLE NO.2
DF40A, DF40A, DF50A, DF50A, DF60A, DF60A
61476-88L00
 
61476-88L00 SEAL, AIR VENT
DF40A, DF40A, DF50A, DF50A, DF60A, DF60A
Back to top