18590-53A01 Suzuki SENSOR, AIR PRESSURE

1. Remove bolts (1) that hold the elbow in position on the oil pump. Remove bolt (2) and lock that fastens the suction bell to the oil pan plate.
The oil pump idler gear (5) can fall off the pump when the pump is removed. To prevent injury, always hold gear on the pump when the pump is removed.
2. Bend the two tabs on the locks on the left hand side of the engine. Remove the four bolts (3) and (4) that fasten the oil pump to the cylinder block. Remove the oil pump and suction bell as a unit. The weight of the unit is 16 kg (35 lb.). Remove idler gear (5) from the oil pump.Install Oil Pump
1. Install idler gear (2) on the oil pump. Put the oil pump (1) in position on the cylinder block. Be sure idler gear (2) is engaged with the crankshaft gear and the tabs on locks on the left hand mounting bolts are not next to the oil pan gasket surface when the bolts are tightened. 2. Install bolts (3) that fasten the gasket and elbow to the oil pump.3. Install the lock and bolt (4) that hold the suction bell to the oil pan plate.End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) and a press as follows:a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in.) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) and a press as follows:a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP in SPECIFICATIONS.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11), cover (12) and bolt (6) in the oil pump body assembly. 6. Install gears and shafts (5) in the oil pump body assembly.7. Install spacer (4) and the two keys in shafts (5). 8. Install two gears and scavenge pump body assembly (13).9. Install key (14), drive gear (2), the washer and bolt (15). Tighten the bolt to a torque of 43 7 N m (32 5 lb.ft.).10. Install the bearing in the idler gear with tooling (A) and a press until it is even with the outside surface of the gear.11. Install the idler gear and suction bell.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump