57110-94313 Suzuki SHAFT, DRIVE


57110-94313 SHAFT, DRIVE Suzuki DT40 SHAFT
57110-94313 SHAFT, DRIVE Suzuki
Rating:
63

Buy SHAFT, DRIVE 57110-94313 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

DT40   Suzuki

Suzuki entire parts catalog list:

DT40 1983

Information:

Starting the Engine
Refer to the Owner's Manual of the OEM for your type of controls. Use the following procedure to start the engine.
Place the transmission in NEUTRAL. Disengage the flywheel clutch to allow the engine to start faster, and to reduce the draining of the battery.
Turn the ignition switch to the ON position.During the key on, the diagnostic lamp, and warning lamp will be checked for proper bulb operation. If any of the lamps do not illuminate, replace the bulb.
Do not engage the starting motor when flywheel is turning. Do not start the engine under load.If the engine fails to start within 30 seconds, release the starter switch or button and wait two minutes to allow the starting motor to cool before attempting to start the engine again.
Push the start button or turn the ignition switch to the START position to crank the engine.Do not push down or hold the throttle down while the engine is cranked. The system will automatically provide the correct amount of fuel that is needed to start the engine.
If the engine fails to start within 30 seconds, release the start button, or the ignition switch. Wait for 2 minutes to allow the starting motor to cool before attempting to start the engine again.
Oil pressure should rise within 15 seconds after the engine starts. Do not increase engine rpm until the oil pressure gauge indicates normal. If oil pressure is not indicated on the gauge within 15 seconds, DO NOT operate the engine. STOP the engine, investigate and correct the cause.
Allow the engine to idle for approximately 3 minutes. Idle the engine until the water temperature gauge has begun to rise. Check all gauges during the warmup period.Note: Oil pressures and fuel pressures should be in the normal range on the instrument panel. Engines that are equipped with "" lamps do not have an operating range. The " and DIAGNOSTIC" lamp (if equipped) will flash while the engine is cranking. The lamp should turn off after proper engine oil pressure or fuel pressure is achieved. Do not apply a load to the engine or increase engine rpm until the oil pressure gauge indicates at least normal pressure. Inspect the engine for leaks and/or unusual noises.If the engine is operated with a low load, the engine will reach normal operating temperature sooner than idling the engine with no load. When the engine is idled in cold weather, increase the engine rpm to approximately 1000 to 1200 rpm to warm up the engine more quickly. Do not exceed the recommended rpm to increase the speed of the warmup. Limit unnecessary idle time to 10 minutes.Starting Problems
An occasional starting problem may be caused by one of the following items:
Low battery charge
Lack of fuel
Problem with the wiring harnessIf the engine fuel system has been run dry, fill the fuel tank and prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime" topic (Maintenance Section).If the other problems are suspected, perform the appropriate procedure to start the engine.Problems with the Wiring Harness
Illustration 1 g01248812
ECM Connector J2/P2
Locate the ECM. Check the connector to ensure that the connector is secure. Lightly pull each of the wires in the chassis harness.
Pull each wire with approximately 4.5 kg (10 lb) of force. The wire should remain in the connector.
If a wire is loose, push the wire back into the connector. Pull the wire again to ensure that the wire is secure.
Start the engine. If the engine does not start, consult the nearest Caterpillar dealer for assistance.


Parts shaft Suzuki:

41130-94300
 
41130-94300 Shaft, Bracket
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT60CLD, DT60CLE
21210-94301
 
21210-94301 Shaft, Clutch
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT60CLD
13410-94300
41130-94330
 
41130-94330 SHAFT, BRACKET
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40
21210-94311
67410-94301-02M
57110-94350
57610-94301
Back to top