45700-98501-0ED SHALLOW DRIVE SET (GRAY) Suzuki
DT6
SHALLOW
Price: query
Rating:
Number on catalog scheme: 26
Compatible models:
DT6
Suzuki
Suzuki entire parts catalog list:
- SWIVEL BRACKET » 45700-98501-0ED
Information:
Problem
Structural cracking of the cab, operators' module, and hood may be a problem on certain D9N and D10N Tractors used in severe or high speed applications.
Affected Product
Model & Identification Number
D9N (1JD1-2100, 1JD2102, 1JD2103, 1JD2107-2110, 1JD2119-2121, 1JD2123, 1JD2128-2130, 1JD2137, 1JD2138)
D10N (2YD1-1298, 2YD1300, 2YD1301, 2YD1303, 2YD1305)
Parts Needed
2 - 8E3217 Plate4 - 8E2646 Plate1 - 8E7290 Snubber Group5 - 5P1076 Washer (D9N Only)16 - 9P2704 Plate (D10N Only)2 - 7T1778 Plate16 - 7T5422 Plate (D9N Only)4 - 8T8917 Bolt (D9N Only)4 - 6V8188 Nut (D9N Only)2 - Gusset (X) (D9N Only)2 - Plate (Y) (D9N Only)1 - Plate A - LH Module Mount1 - Plate B - RH Module MountAction Required
See the attached procedures.
Service Claim Allowances
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.
(1-Cab, Module, and Fender Procedure)(2-Hood Inspection and Repair Procedure [D10N only])(3-Undercarriage Inspection And Repair Procedure)Cab, Module and Fender Procedure
All parts used in this procedure are part of the 8E7290 Snubber Group.
1. Inspect the cab and operators' module for cracks paying particular attention to the areas shown by Illustrations 1 thru 7.2. If the rear module support brackets (Illustrations 1 and 2) are cracked, it will be necessary to remove the cab and module from the tractor to perform the repair.3. Repair the cracks in the cab structure as outlined by the following weld repair procedure.a. Locate the end of the crack. Mark it with a center punch, then drill a 3.18 mm (.125") diameter hole at that location.b. Use a small grinder to vee out the crack.c. Weld repair the crack with a MIG welder using 1.14 mm (.045") solid wire and
Structural cracking of the cab, operators' module, and hood may be a problem on certain D9N and D10N Tractors used in severe or high speed applications.
Affected Product
Model & Identification Number
D9N (1JD1-2100, 1JD2102, 1JD2103, 1JD2107-2110, 1JD2119-2121, 1JD2123, 1JD2128-2130, 1JD2137, 1JD2138)
D10N (2YD1-1298, 2YD1300, 2YD1301, 2YD1303, 2YD1305)
Parts Needed
2 - 8E3217 Plate4 - 8E2646 Plate1 - 8E7290 Snubber Group5 - 5P1076 Washer (D9N Only)16 - 9P2704 Plate (D10N Only)2 - 7T1778 Plate16 - 7T5422 Plate (D9N Only)4 - 8T8917 Bolt (D9N Only)4 - 6V8188 Nut (D9N Only)2 - Gusset (X) (D9N Only)2 - Plate (Y) (D9N Only)1 - Plate A - LH Module Mount1 - Plate B - RH Module MountAction Required
See the attached procedures.
Service Claim Allowances
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.
(1-Cab, Module, and Fender Procedure)(2-Hood Inspection and Repair Procedure [D10N only])(3-Undercarriage Inspection And Repair Procedure)Cab, Module and Fender Procedure
All parts used in this procedure are part of the 8E7290 Snubber Group.
1. Inspect the cab and operators' module for cracks paying particular attention to the areas shown by Illustrations 1 thru 7.2. If the rear module support brackets (Illustrations 1 and 2) are cracked, it will be necessary to remove the cab and module from the tractor to perform the repair.3. Repair the cracks in the cab structure as outlined by the following weld repair procedure.a. Locate the end of the crack. Mark it with a center punch, then drill a 3.18 mm (.125") diameter hole at that location.b. Use a small grinder to vee out the crack.c. Weld repair the crack with a MIG welder using 1.14 mm (.045") solid wire and