09160-08007 Suzuki Spacer, Swivel Bracket


09160-08007 Spacer, Swivel Bracket Suzuki DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT4.5LB, DT4.5SB, DT4D Spacer
09160-08007 Spacer, Swivel Bracket Suzuki
Rating:
93

Buy Spacer, Swivel Bracket 09160-08007 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Suzuki entire parts catalog list:

DT35CRLH 1987
DT35CRLJ 1988
DT35CRLK 1989
DT35CRSH 1987
DT35CRSJ 1988
DT35CRSK 1989
DT35MCLH 1987
DT35MCLJ 1988
DT35MCLK 1989
DT35MCSH 1987
DT35MCSJ 1988
DT35MCSK 1989
DT35TCLH 1987
DT35TCLJ 1988
DT35TCLK 1989
DT4.5LB 1977
DT4.5SB 1977
DT4D 1978

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the engine is equipped, with a cover over the fuel system the cover will need to be removed.
Disconnect the breather hose from the separator for the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.
Illustration 1 g01335890
Cut the cable straps that secure the harness assembly to inlet manifold (4). Position the harness assembly away from the inlet manifold.
Remove bolts (1) from inlet connection (2).
Remove inlet connection (2) and gasket (3) from inlet manifold (4).
Remove bolts (5).
Remove inlet manifold (4) from the cylinder head. Use a suitable tool to pry the inlet manifold from the cylinder head. Use the recess at Position (X) to pry the inlet manifold.
Remove inlet manifold seal (6) from the recess in inlet manifold (4).
Do not remove two dowel pins (7). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 2431 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01335909
Ensure that the inlet manifold is clean and free from damage. If necessary, replace the inlet manifold. If a new inlet manifold is installed, install two new dowel pins (7) to inlet manifold (4). Note: Do not install dowel pins to the cylinder head.
Clean the gasket surface of the cylinder head.
Align tag (8) to the slot at Position (Y) on the inlet manifold. Install new seal (6) to the groove in inlet manifold (4). Ensure that the seal is correctly located.
Align dowel pins (7) to the holes in the cylinder head. Install inlet manifold (4) to the cylinder head.
Apply Tooling (A) to bolts (5). Install the bolts to inlet manifold (4).
Illustration 3 g01335892
Tighten the bolts to a torque of 22 N m (16 lb ft) in the sequence that is shown in Illustration 3.
Ensure that inlet connection (2) is clean and free from damage. If necessary, replace the inlet connection.
Position a new gasket (3) onto the inlet manifold. Install inlet connection (2) to inlet manifold (4).
Install bolts (1) to inlet connection (2). Tighten the bolts to a torque of 22 N m (16 lb ft).
Install the air temperature sensor. Refer to Disassembly and Assembly, "Inlet Air Temperature Sensor - Remove and Install" for the correct procedure.
Install the boost pressure sensor. Refer to Disassembly and Assembly, "Boost Pressure Sensor - Remove and Install" for the correct procedure.
Position the harness assembly on the inlet manifold. Use new cable straps in order to secure the harness assembly.
Connect the breather hose to the separator for the crankcase breather (not shown). Refer to Disassembly and Assembly, "Crankcase Breather - Install" for the correct procedure.
If the engine is equipped, with a cover over the fuel system the cover will need to be installed. End By:
Install the ECM mounting bracket. Refer to Disassembly and Assembly, "ECM Mounting Bracket - Remove and Install" for the correct procedure.
Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold - Install" for the correct procedure.
If necessary, install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.


Parts spacer Suzuki:

09180-06007
 
09180-06007 Spacer, Clamp Shaft
DT4.5LB, DT4.5SB, DT4D, DT7.5LB, DT7.5LC, DT7.5LN, DT7.5SB, DT7.5SC, DT7.5SN, DT9C, DT9D, DT9F
09180-08069
 
09180-08069 Spacer, Swivel Shaft
DT4.5LB, DT4.5SB, DT4D
65341-98000
 
65341-98000 Spacer, Fuel Cock
DT4.5LB, DT4.5SB, DT4D
09320-10002
 
09320-10002 Spacer, Tank Cushion
DT4.5LB, DT4.5SB, DT4D
09180-08085
 
09180-08085 SPACER
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT50, DT50, DT50M, DT50W, DT65, DT65
67721-94300
 
67721-94300 Spacer
30ELE, 30ESE, 30MLE, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25C, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25ML
19161-94301
 
19161-94301 Spacer, stator
30ELE, 30ESE, 30MLE, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25MLJ, DT25
43713-94400
 
43713-94400 SPACER, STEERING BUSH
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C
Back to top