09180-12087 Suzuki SPACER (12x16.5x6.5)


09180-12087 SPACER (12x16.5x6.5) Suzuki DT50, DT50, DT50M, DT50W, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, D SPACER
09180-12087 SPACER (12x16.5x6.5) Suzuki
Rating:
93

Buy SPACER (12x16.5x6.5) 09180-12087 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50 1983
DT50M 1980,1981,1982
DT50W 1980,1981,1982
DT55CLF 1985
DT55CRLG 1986,1987
DT55CRLJ 1988
DT55CRLK 1989
DT55CRLL 1990
DT55CRSG 1986
DT55CRSH 1987
DT55HTCLH 1987
DT55HTCLJ 1988
DT55HTCLK 1989
DT55HTCLL 1990
DT55TCLG 1986
DT55TCLH 1987
DT55TCLJ 1988
DT55TCLK 1989
DT55TCLL 1990
DT55TCLM 1991
DT55TCLN 1992
DT55TCLP 1993
DT55TCLR 1994
DT55TCLS 1995
DT55TCLT 1996
DT55TCLV 1997
DT55TCSG 1986
DT55TCSH 1987
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982
DT65CRLG 1986
DT65CRLH 1987
DT65CRLJ 1988
DT65CRLK 1989
DT65CRLL 1990
DT65CRSG 1986
DT65CRSH 1987
DT65HTCLK 1989
DT65HTCLL 1990
DT65TCLF 1985
DT65TCLG 1986
DT65TCLH 1987
DT65TCLJ 1988
DT65TCLK 1989
DT65TCLL 1990
DT65TCLM 1991
DT65TCLN 1992
DT65TCLP 1993
DT65TCLR 1994
DT65TCLS 1995
DT65TCLT 1996
DT65TCLV 1997
DT65TCSG 1986
DT65TCSH 1987

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Specifications
Table 1
Inlet and Exhaust Valve Lash Specifications
Setting Type Specification
C13 Inlet Valve Lash 0.38 0.08 mm (0.015 0.003 inch)
C13 Exhaust Valve Lash 0.76 0.08 mm (0.030 0.003 inch)
C15/C18 Inlet Valve Lash 0.38 0.08 mm (0.015 0.003 inch)
C15/C18 Exhaust Valve Lash 0.81 0.08 mm (0.032 0.003 inch)
Table 2
Compression Brake Lash Specifications
Setting Type Specification
C13 Compression Brake Valve Lash 0.711 0.05 mm (0.028 0.002 inch)
C15/C18 Compression Brake Valve Lash 0.686 0.05 mm (0.0270 0.002 inch)
Table 3
Variable Valve Actuator Lash Specifications
Setting Type Specification
C15/C18 Variable Valve Actuator Valve Lash 0.50 0.08 mm (0.020 0.003 inch)
Table 4
Fuel Injector Specifications
Setting Type Specification
Fuel Injector Settings Turn to touch and extra 180 degree turn Introduction
Use the procedure below to inspect and adjust the valve mechanism lash settings.Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.References
Reference: Testing and Adjusting, Finding Top Center Position No. 1 PistonReference: Disassembly and AssemblyMechanical Electronic Injector Unit (MEIU) and Valve Lash Adjustment Procedure
Put the number 1 piston at Top Dead Center (TDC) on the compression stroke. Refer to the Testing and Adjusting, Finding Top Center Position No. 1 Piston.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 1 will move freely. If the valves do not move freely, cylinder number 1 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.
Table 5
TDC No. 1 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash C13
0.38 0.08 mm (0.015 0.003 inch)
C15 and C18
0.38 0.08 mm (0.015 0.003 inch) C13
0.76 0.08 mm (0.030 0.003 inch)
C15 and C18
0.81 0.08 mm (0.032 0.003 inch)
Cylinders 1–2–4 1–3–5
Adjust the valve lash using the specifications from Table 5.
Lightly tap the rocker arm with a soft mallet.Note: This ensures that the roller lifter seats against the base circle of the camshaft.
Loosen the adjustment locknut for the appropriate valves.
Place the feeler gauge between the rocker arm and the valve bridge.
Turn the adjustment screw in a clockwise direction while sliding the feeler gauge back and forth between the rocker arm and valve bridge. Continue turning the adjustment screw in a clockwise direction until a slight drag is felt on the feeler gauge.
Tighten the adjustment locknut to 30 7 N m (22 5 lb ft).Note: Do not allow the adjustment screw to turn while torquing the locknut.
Recheck the valve lash after tightening the adjustment locknut. Remove the feeler gauge.
Follow the steps below to set the mechanical unit injectors on TDC of number 1 piston compression stroke.Note: Injectors for cylinders 3, 5, and 6 can be adjusted at TDC of number 1 piston compression stroke.
Loosen the adjustment locknut for the injector.
Turn the adjustment screw clockwise until the screw contacts the mechanical electronic unit injector.
Turn the adjustment screw an extra two turns clockwise to push all the fuel out of the injector plunger.Note: The additional turns will ensure the injector pre-load is set accurately.
Turn the adjustment screw counter-clockwise for 2.5 turns.
Turn the adjustment screw clockwise until the screw contacts the injector.
Turn the screw clockwise an extra 180 degrees or half turn.
Tighten the locknut to 55 10 N m (41 7 lb ft) while not allowing the adjustment screw to turn for C13 engines. Tighten the locknut to 100 10 N m (74 7 lb ft) while not allowing the adjustment screw to turn for C15 and C18 engines
Remove the timing pin and rotate the engine 360 degrees in the direction of engine rotation. This will put the engine at TDC of number 6 piston. Pin the flywheel with the timing pin.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 6 will move freely. If the valves do not move freely, cylinder number 6 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.


Parts spacer Suzuki:

09180-06035
 
09180-06035 Spacer 6.1x8x12
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M
57633-95302
 
57633-95302 Spacer, propeller nut
DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT65, DT65, DT65ELC, DT65ELN, DT65ESC, DT65ESN
09180-06044
 
09180-06044 Spacer
DT14D, DT14F, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT50, DT50, DT50M, DT50W, DT65, DT65, DT65ELN, DT65ESN, DT75TCLD, DT75TCLE, DT75TCLF, DT85ELT, DT85TCLD, DT85TCLE, DT85TCLF, DT85TCLT, DT85TCLX, DT85TCLZ, D
48325-95500
 
48325-95500 Spacer
DT50, DT50M, DT50W, DT65, DT65, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELN, DT85TELT
57633-95303
 
57633-95303 SPACER, PROPELLER NUT
DT50, DT50M, DT50W, DT65, DT65
63115-96300
09180-06289
SPACER
09180-06289 SPACER
DF150, DF175, DT25C, DT30C, DT30CRLJ, DT30CRSJ, DT30MCLJ, DT30MCSJ, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN,
09180-06310
SPACER
09180-06310 SPACER
DF4, DF4, DF4, DF4L, DF6, DF6, DF6, DF6L, DT40C, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR
Back to top