09440-21005 Suzuki SPRING


09440-21005 SPRING Suzuki DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT55TCSG, DT55TCS SPRING
09440-21005 SPRING Suzuki
Rating:
33

Buy SPRING 09440-21005 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Suzuki entire parts catalog list:

DT55CLF 1985
DT55CRLG 1986,1987
DT55CRLJ 1988
DT55CRLK 1989
DT55CRLL 1990
DT55CRSG 1986
DT55CRSH 1987
DT55HTCLH 1987
DT55HTCLJ 1988
DT55HTCLK 1989
DT55HTCLL 1990
DT55TCLG 1986
DT55TCLH 1987
DT55TCLJ 1988
DT55TCLK 1989
DT55TCLL 1990
DT55TCLM 1991
DT55TCLN 1992
DT55TCLP 1993
DT55TCLR 1994
DT55TCLS 1995
DT55TCLT 1996
DT55TCLV 1997
DT55TCSG 1986
DT55TCSH 1987
DT65CRLG 1986
DT65CRLH 1987
DT65CRLJ 1988
DT65CRLK 1989
DT65CRLL 1990
DT65CRSG 1986
DT65CRSH 1987
DT65HTCLK 1989
DT65HTCLL 1990
DT65TCLF 1985
DT65TCLG 1986
DT65TCLH 1987
DT65TCLJ 1988
DT65TCLK 1989
DT65TCLL 1990
DT65TCLM 1991
DT65TCLN 1992
DT65TCLP 1993
DT65TCLR 1994
DT65TCLS 1995
DT65TCLT 1996
DT65TCLV 1997
DT65TCSG 1986
DT65TCSH 1987

Information:

1. Remove lubrication supply line (4) for the turbocharger.2. Disconnect control linkage (1) from governor.3. Disconnect fuel injection lines (2). Put a cap on all openings.4. Remove breather tube (3).5. Remove bolts that hold fuel injection pump housing to the accessory drive housing.6. Loosen two bolts in bracket (5). 7. Remove the governor and fuel injection pump housing (6) as a unit. Weight is 48 lb. (22 kg).Install Fuel Injection Pump Housing And Governor
1. Remove timing plug (1) from the flywheel housing.2. Turn crankshaft clockwise as seen from the front of the engine (rear of machine) until a 3/8"-16 NC bolt, 2 1/4 in. long can be installed in the flywheel through the timing hole. If the timing hole in the flywheel is turned too far, do not turn the crankshaft back. Turn the crankshaft two more turns, until bolt can be installed. 3. Remove crankcase breather (2) from valve cover.4. When No. 1 piston is at top center compression position, the intake and exhaust rocker arms for No. 1 cylinder can be moved through the breather hole in the valve cover.5. If either of the rocker arms can not be moved, remove the timing bolt and turn the crankshaft 360° and install the timing bolt again.6. Install tool (A) on the rear face of the accessory drive housing. Install the plate with the dowels in the accessory drive housing in alignment with the dowel holes in the plate. If the timing fixture can be installed, the timing is correct. If the timing fixture can not be installed, use the following procedure in Steps 7 through 11 to get accessory drive in time.7. Loosen the alternator and remove the belts from the pulley. 8. Remove cover (3) from timing gear cover. 9. Remove the nut and washer from the accessory drive gear. Install tooling (B) and loosen gear on shaft. Remove tooling.10. Turn accessory drive shaft enough to install tool (A). 11. Install washer (4) so the outer edge makes contact with the gear first. Install nut (5) and tighten to a torque of 100 10 lb.ft. (135 14 N m).12. Put the fuel injection pump housing and governor in position on the engine. Install bolts that hold it to the accessory drive housing.13. Tighten two bolts in bracket (8).14. Install crankcase breather and tube.15. Install tubocharger supply line (7). 16. Connect control linkage (6) to governor.17. Remove the caps and connect the fuel lines to pumps. Tighten the nuts on the lines to a torque of 30 5 lb.ft. (40 7 N m).18. Remove the timing bolt and install the plug.Separation Of Governor From Fuel Injection Pump Housing
start by:a) remove fuel injection pump housing and governor 1. Remove the cover (1).2. Remove the screw (2) for the rack stop collar.3. Remove rack stop collar (3).4. Remove the bolts (4) that hold the governor to the housing of injection pumps. 5. Remove the governor housing (5).6. Remove the governor spring and seat from the guide in housing (5).7. Remove the washer type spring (6) from bolt.8. Remove the three bolts (7) and lock that hold the cylinder and weight (8) to the housing of injection pumps.9. Pull the cylinder and weight assemblies straight out until they are free of dowels. 10. Slide the cylinder and weight assemblies to the side to free the piston from rack (9).Connection Of Governor To Fuel Injection Pump Housing
1. Put the cylinder and weight assemblies (1) in position on the housing of injection pumps so the piston (2) is in correct location on the rack (3).2. Push the cylinder and weight assemblies on to the location dowels. 3. Install the three bolts (4) and lock.4. Install the washer type spring (5) on bolt (6).5. Put the seat and governor spring on guide in governor housing. The washer type spring (5) must be installed so the inside diameter of spring will be against the guide in governor housing (7).6. Put the governor housing (7) in position on housing of injection pumps, and install the bolts. 7. Install the rack stop collar (8) on bolt (6).8. Put the idle screw cover (10) in position on the governor housing so the dowel (11) in housing is engaged with groove (slot) (12) in the rack stop collar.9. Install the bolts that hold the idle screw cover to the governor housing.end by: a) install fuel injection pump housing and governorb) make an adjustment to the rack and governor (See FUEL RACK SETTING AND GOVERNOR ADJUSTMENTS in TESTING AND ADJUSTING)


Parts spring Suzuki:

13271-93311
Spring, air screw
13271-93311 Spring, air screw
20ELB, 20ELC, 20ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT115, DT140, DT20ELG, DT20ELH, DT20ELJ, DT20ESB, DT20ESC, DT20ESG, DT20ESH, DT20ESJ, DT20ESN, DT20MLB, DT20MLC, DT20MLG, DT20MLH, DT20MLJ, DT20MLN, DT20MSB, DT20MSC, DT20MSG, DT20MSH, DT20MSJ,
09441-21002
 
09441-21002 Spring, tilt lock pin
DT50, DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, D
09205-02004
 
09205-02004 Spring Pin
30ELE, 30ESE, 30MLE, DF15, DF15, DF15, DF15A, DF15S, DF20A, DF25, DF25(R)S, DF25Q, DF25Q(QR), DF25R, DF25R, DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF4, DF4, DF4, DF40, DF40, DF40A, DF40A, DF40QH, DF40TL, DF46, DF4L, DF50, DF50, DF50A, DF50A, DF50QH, D
09440-26002
 
09440-26002 Spring, preload
DT50, DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, D
13268-96111
Spring
13268-96111 Spring
DF15, DF15, DF15S, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF9.9R, DF9.9RL, DF9.9S, DF9.9TH, DF9.9TH, DF99R, DF99TH, DT115, DT140, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, D
09448-27010
 
09448-27010 SPRING
DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT55TCSG, DT55TCS
09448-27011
 
09448-27011 SPRING
DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT55TCSG, DT55TCS
09440-09021
 
09440-09021 SPRING
DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT55TCSG, DT55TCS
Back to top