09440-41002 Suzuki Spring, dog

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed with the draining cold oil. Drain the crankcase with the engine stopped. Drain the crankcase with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will cause the waste particles to be recirculated through the engine lubrication system with the new oil.Interval for Engine Oil and Engine Oil Filter Change
Refer to this Operation and Maintenance Manual, "Refill Capacities" before this procedure is started in order to determine the following:
The type of oil pan
The refill capacity for engine oil
Table 1
Intervals for Changing the Engine Oil and Engine Oil Filter(1)
Shallow sump Every 12870 L (3400 US gal) or 250 service hours or 1 yr
Deep sump Every 15900 L (4200 US gal) or 500 service hours or 1 yr
(1) Choose the interval that occurs first.Drain the Engine Oil
After the engine has been run at the normal operating temperature, stop the engine. Attach a "DO NOT OPERATE" or a similar warning tag to the ignition keyswitch before the engine is serviced.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Remove the oil drain plug in order to allow the oil to drain.
After the oil has drained, the oil drain plug should be cleaned and installed. Replace the Oil Filter
Caterpillar oil filters are built to Caterpillar specifications. Use of an oil filter not recommended by Caterpillar could result in severe engine damage to the engine bearings, crankshaft, etc., as a result of the larger waste particles from unfiltered oil entering the engine lubricating system. Only use oil filters recommended by Caterpillar.
Illustration 1 g00103713
Typical filter mounting base and filter gasket
Remove the oil filter with a 185-3630 Strap Wrench.
Clean the sealing surface of the filter mounting base. Ensure that all of the old oil filter gasket is removed.
Apply clean engine oil to the new oil filter gasket.
Do not fill the oil filters with oil before installing them. This oil would not be filtered and could be contaminated. Contaminated oil can cause accelerated wear to engine components.
Install the oil filter. Tighten the oil filter until the oil filter gasket contacts the base. Tighten the oil filter by hand according to the instructions that are shown on the oil filter. Do not overtighten the oil filter. Fill the Engine Crankcase
Remove the oil filler cap. Fill the crankcase with the proper amount of oil. Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for information about engine oils.
If equipped with an auxiliary oil filter or system, extra oil must be added when filling the crankcase. Follow the OEM or filter manufacturer's recommendations. If the extra oil is not added, the engine may starve for oil.
To help prevent crankshaft or bearing damage, crank engine to fill all filters before starting. Do not crank engine for more than 30 seconds.
Start the engine and run the engine at "LOW IDLE" for 2 minutes. Perform this procedure in order to ensure that the lubrication system has oil and that the oil filters are filled. Inspect the oil filter for oil leaks.
Stop the engine and allow the oil to drain back to the sump for a minimum of 10 minutes.
Remove the oil level gauge in order to check the oil level. Maintain the oil level between the "ADD" and "FULL" marks on the "ENGINE STOPPED" side of the oil level gauge.