48843-87D00 Suzuki SPRING

1. Remove two bolts (1).2. Remove two nuts (2). Aside infill assembly.
Always wear goggles when working on air conditioning systems. The system is under pressure at all times, engine running or not. Escaping Freon-12 (C C12F2 Dichloro Difluoro Methane) can cause freezing of human flesh.DO NOT SMOKE WHILE WORKING ON AIR CONDITIONING SYSTEMS. Inhaling Freon-12 through any smoking material, although not toxic or flammable, can generate phosgene gas and cause violent illness. ALSO, HEAT MUST NEVER BE APPLIED TO A CHARGED SYSTEM. See Air Conditioning & Heating Service Manual, Form No. SENR3334, for more information on removal and installation of lines and refrigerant from the system.
Use a freon reclaimer before loosening bolt on the two lines.3. Loosen one bolt and disconnect two lines (3). 4. Loosen two hose clamps (4).5. Disconnect two hoses (5). Move hoses to underside of cab. 6. Remove four bolts (6). Aside hose. Cap or plug immediately.7. Remove four bolts (7). Aside hose. Cap or plug immediately. 8. Remove eight bolts (8). Aside flexible pipe.
The front suspension accumulator lines (9) contain extremely high pressure. Make sure all personnel are clear of the machine to avoid injury. Then, depress the handle on the bottom of the suspension valve. The front suspension cylinders will quickly retract, lowering the machine.
9. Remove three lines (9) by removing twelve bolts. Cap or plug immediately. The left line is not visible in the photo.10. Disconnect hose fitting (11). Cap or plug immediately.11. Disconnect six electrical quick connections (10). Mark and identify for connection during installation procedure. 12. Remove four bolts (12). Cap or plug off immediately.13. Disconnect two electrical quick connections (13). 14. Remove four bolts (14). 15. Disconnect air hose line (15). Remove three tyraps securing line.16. Disconnect hose (16) on top of fuel injection pump. Cap or plug off immediately. 17. Remove nut (17) from governor accelerator linkage.18. Remove the two nuts from u-bolt clamp (18). 19. Disconnect two hose fittings (19). Cap or plug off immediately.20. Disconnect hose (20) from fuel transfer pump. Cap or plug off immediately. 21. Remove clamp bolt (21).22. Remove positive cable nut (22).23. Remove negative cable nut (23). 24. Remove three lines (24) by removing twelve bolts. Cap or plug off immediately. Photo shows removals and disconnects already completed.25. Remove two lines (25) from clutch lockout valve. Cap or plug off immediately.26. Disconnect speed sensor (26). Cap or plug off immediately.27. Disconnect electrical quick connection (27). 28. Remove hose (28) from retarder relief valve on the bottom side of the retarder. Cap or plug off immediately. 29. Remove hose (29) by removing four bolts. Cap or plug off immediately. 30. Remove nut (30). 31. Remove nut (31) on the right hand engine mount. Repeat this procedure for the left hand engine mount. 32. Attach hoist to engine. Raise engine slightly. Then, remove the four bolts and left hand engine mount for clearance when removing engine, retarder, and torque convertor from tractor.33. Remove engine, retarder, and torque convertor from tractor. Observe for any possible connections when removing engine, retarder, and torque convertor from tractor.34. Check all seals and O-rings for damage or wear before assembling, replace as necessary. For installation of the engine, retarder, and torque convertor, reverse the removal steps.End By:a. install ether aid groupb. install engine hoodc. install radiatord. install suction & guard fan groupe. install radiator guardf. install fuel tankg. install dust ejectorh. install dust guardi. install crankcase guard groupj. fill all systems to proper capacitySeparation & Connection, Engine From Torque Convertor Arrangement
Start By:a. remove engine, retarder and torque convertor arrangement 1. Remove & mark electrical disconnects (1) for correct location during assembly.2. Remove bolt (4) at bracket (2).3. Remove bolt (7) at harness clip (6). Set electrical harness (8) aside.4. Remove four bolts (3) from two half flanges (5). 5. Remove two bolts (11) from oil baffle tube (9).6. Remove eight bolts (12). Set aside four half flanges (10). 7. Attach tool (A) to torque convertor arrangement (13) and fasten with hoist.8. Remove ten bolts (14). Remove torque convertor arrangement (13) aside. The torque convertor arrangement weighs 563 kg (1250 lb). Check all the O-rings for wear or damage before connection, replace if necessary. For connection of the torque convertor arrangement, reverse the separation steps.End By:a. install the engine, retarder and torque convertor arrangement