41111-95281-0ED Suzuki STARBOARD CLAMP BRACKET


41111-95281-0ED STARBOARD CLAMP BRACKET Suzuki DT55CLF, DT55CRLG, DT55CRSG, DT55CRSH, DT55HTCLH, DT55TCLG, DT55TCLH, DT55TCSG, DT55TCSH, DT65CRLG, DT65CRLH, DT65CRSG, DT65CRSH, DT65TCLF, DT65TCLG, DT65TCLH, DT65TCSG, DT65TCSH STARBOARD
41111-95281-0ED STARBOARD CLAMP BRACKET Suzuki
Rating:
73

Buy STARBOARD CLAMP BRACKET 41111-95281-0ED Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Suzuki entire parts catalog list:

DT55CLF 1985
DT55CRLG 1986,1987
DT55CRSG 1986
DT55CRSH 1987
DT55HTCLH 1987
DT55TCLG 1986
DT55TCLH 1987
DT55TCSG 1986
DT55TCSH 1987
DT65CRLG 1986
DT65CRLH 1987
DT65CRSG 1986
DT65CRSH 1987
DT65TCLF 1985
DT65TCLG 1986
DT65TCLH 1987
DT65TCSG 1986
DT65TCSH 1987

Information:

Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Illustration 1 g06512670
Typical example
(1) Idler gear 2
(2) Balancer gear 1
(3) Idler gear 1
(4) Balancer gear 2Inspect the gears for wear or for damage. If the gears are worn or damaged, use new parts for replacement. Refer to Disassembly and Assembly for more information.Backlash for Balancer Gears
Backlash Between the Crankshaft Gear and the Balancer Idler Gear 1
Use Tooling (A) to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, Finding Top Center Position for No.1 Piston for the correct procedure.
Remove Tooling (B) from the camshaft.
Remove the flywheel. Refer to Disassembly and Assembly, Flywheel - Remove for the correct procedure.
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, Crankshaft Rear Seal - Remove and Install for the correct procedure.
Mount Tooling (C) on a suitable flat surface to measure the backlash between the crankshaft gear and the balancer idler gear 1. Ensure that the point of the finger attachment is in contact with the balancer idler gear 1. The backlash measurement point is half way down the pitch circle diameter and along the relevant tooth.
Set the dial gauge indicator to zero. Gently rotate the balancer idler gear 1 backwards and forwards. Measure the backlash between the crankshaft gear and the balancer idler gear 1 in both directions. Refer to Specifications, "Gear Group (Rear) - Engines with a Balancer" for the backlash measurement.Note: Apply a sufficient force to be able to rotate the balancer idler gear 1, but not enough force to rotate the crankshaft.Backlash Between the Balancer Idler Gear 1 and the Balancer Idler Gear 2
Remove the engine oil pan. Refer to Disassembly and Assembly, Engine Oil Pan - Remove and Install - Cast Iron Oil Pan With Balancer for the correct procedure.
Use a suitable tool to clamp balancer idler gear 2 in position. Ensure that balancer idler gear 2 is not damaged when the operation is performed.
Mount Tooling (C) on a suitable flat surface to measure the backlash between the balancer idler gear 1 and the balancer idler gear 2. Ensure that the finger attachment is vertical. Ensure that the point of the finger attachment is in contact with the balancer idler gear 1. The backlash measurement point is half way down the pitch circle diameter and along the relevant tooth.
Ensure that the other gears that mesh with balancer idler gear 1 can rotate freely. The other gears should not restrict the movement of the gear that is being measured.
Set the dial gauge indicator to zero. Gently rotate the balancer idler gear 1 backwards and forwards. Measure the backlash between the balancer idler gear 1 and the balancer idler gear 2. Refer to Specifications, "Gear Group (Rear) - Engines with a Balancer" for the backlash measurement.Note: Apply a sufficient force to be able to rotate the balancer idler gear 1, but not enough force to damage the locking tool.Backlash Between the Balancer Idler Gear 1 and the Balancer Gear 2
Use a suitable tool to clamp balancer gear 2 in position. Ensure that balancer gear 2 is not damaged when the operation is performed.
Mount Tooling (C) on a suitable flat surface to measure the backlash between the balancer idler gear 1 and the balancer gear 2. Ensure that the finger attachment is vertical. Ensure that the point of the finger attachment is in contact with the balancer idler gear 1. The backlash measurement point is half way down the pitch circle diameter and along the relevant tooth.
Ensure that the other gears that mesh with balancer idler gear 1 can rotate freely. The other gears should not restrict the movement of the gear that is being measured.
Set the dial gauge indicator to zero. Gently rotate the balancer idler gear 1 backwards and forwards. Measure the backlash between the balancer idler gear 1 and the balancer gear 2. Refer to Specifications, "Gear Group (Rear) - Engines with a Balancer" for the backlash measurement.Note: Apply a sufficient force to be able to rotate the balancer idler gear 1, but not enough force to damage the locking tool.Backlash Between the Balancer Idler Gear 2 and the Balancer Gear 1
Use a suitable tool to clamp balancer gear 1 in position. Ensure that balancer gear 1 is not damaged when the operation is performed.
Mount Tooling (C) on a suitable flat surface to measure the backlash between the balancer idler gear 2 and the balancer gear 1. Ensure that the finger attachment is vertical. Ensure that the point of the finger attachment is in contact with the balancer idler gear 2. The backlash measurement point is half way down the pitch circle diameter and along the relevant tooth.
Ensure that the other gears that mesh with balancer idler gear 2 can rotate freely. The other gears should not restrict the movement of the gear that is being measured.
Set the dial gauge indicator to zero. Gently rotate the balancer idler gear 2 backwards and forwards. Measure the backlash between the balancer idler gear 2 and the balancer gear 1. Refer to Specifications, "Gear Group (Rear) - Engines with a Balancer" for the backlash measurement.Note: Apply a sufficient force to be able to rotate the balancer idler gear 2, but not enough force to damage the locking tool.
Check the end float for the balancer gears. Refer to "End Float for Balancer Gears" for the correct procedure.End Float for Balancer Gears
If necessary, use Tooling (A) to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, Finding Top Center Position for No.1 Piston for the


Parts starboard Suzuki:

41111-95252-02M
 
41111-95252-02M STARBOARD CLAMP BRACKET
DT55CLF, DT55CRLG, DT55CRSG, DT55CRSH, DT55HTCLH, DT55TCLG, DT55TCLH, DT55TCSG, DT55TCSH, DT65CRLG, DT65CRLH, DT65CRSG, DT65CRSH, DT65TCLF, DT65TCLG, DT65TCLH, DT65TCSG, DT65TCSH
41111-95272-0ED
 
41111-95272-0ED STARBOARD CLAMP BRACKET
DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT55TCSG, DT55TCS
Back to top