06111-05004 Suzuki Ball


06111-05004 Ball Suzuki DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT150TCXGP, DT150TCXGR, Ball
06111-05004 Ball Suzuki
Rating:
58

Buy Ball 06111-05004 Suzuki genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$10.99
 

24-11-2021

-: -
SUZUKI GENUINE PART STEEL BALL 06111-05004
Number on catalog scheme: 30
 

Suzuki entire parts catalog list:

DT150 1998,1999,2000,2001,2002,2003
DT150SSH 1987
DT150SSJ 1988
DT150SSK 1989
DT150SSL 1990
DT150SSM 1991
DT150SSN 1992
DT150STCLP 1993
DT150STCLR 1994
DT150STCLS 1995
DT150STCLT 1996
DT150TCLH 1987
DT150TCLJ 1988
DT150TCLK 1989
DT150TCLL 1990
DT150TCLM 1991
DT150TCLN 1992
DT150TCLP 1993
DT150TCLR 1994
DT150TCXGM 1991
DT150TCXGN 1992
DT150TCXGP 1993
DT150TCXGR 1994
DT150TCXGS 1995
DT150TCXGT 1996
DT150TCXH 1987
DT150TCXJ 1988
DT150TCXK 1989
DT150TCXL 1990
DT150TCXM 1991
DT150TCXN 1992
DT150TCXP 1993
DT150TCXR 1994
DT150TCXS 1995
DT150TCXT 1996
DT200 1998,1999,2000,2001,2002,2003
DT225 1998,1999,2000,2001,2002,2003
DT50 1980,1981,1982
DT50M 1980,1981,1982
DT50W 1980,1981,1982
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982

Information:


Table 1
Diagnostic and Event Codes Table    
Code and Description     Conditions which Generate this Code     System Response    
2271-5
Engine Oil Renewal System Actuation Solenoid : Current Below Normal     The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery in the circuit for the oil renewal solenoid.     The code is logged. The oil renewal system is disabled.    
2271-6
Engine Oil Renewal System Actuation Solenoid : Current Above Normal     The ECM detects a short circuit to ground in the circuit for the oil renewal solenoid.    
E2089(1)
Oil Renewal System Cannot Operate - least severe     The oil renewal system cannot operate.    The ECM adds a controlled amount of engine oil to the fuel by energizing the oil renewal solenoid. The engine oil is added to the fuel and burned during combustion. The typical oil change interval may be extended.For further information, refer to Service Manual, RENR2223, "Oil Renewal System".
Illustration 1 g03367635
Schematic for the oil renewal system
Illustration 2 g03325707
Terminal locations at the P1 ECM connector (P1-20) Oil Renewal System
Illustration 3 g03325708
Terminal locations ar the P2 ECM connector (P2-14) Digital return
Table 2
Troubleshooting Test Steps    Values    Results    
1. Inspect the Electrical Connectors and the Wiring
A. Remove the electrical power from the engine ECM.
B. Thoroughly inspect the J1/P1 and J2/P2 ECM connectors. Inspect all of the other connectors that are in the circuit for the oil renewal solenoid. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
D. Check the allen head screw on each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points.
    Inspect Connectors and Wiring    
Results: The harness and wiring appear to be OK.
Proceed to Test Step 2.
Results: There is a problem in the connectors and/or wiring.
Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
Verify that the repair eliminates the problem.
   
2. Check for Active Diagnostic Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
B. Restore the electrical power to the engine ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Select diagnostic tests from Cat ET.
E. Select the "Override Parameters" screen on Cat ET.
F. Activate the override for the oil renewal solenoid.
G. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
H. Disable the override for the oil renewal solenoid.
I. Remove the electrical power from the engine ECM.
J. Determine if the problem is related to an open circuit diagnostic code -5 or a short circuit diagnostic code -6.
    Active Code    
Results: No diagnostic codes are active.
Repair: There does not appear to be a problem with the oil renewal solenoid at this time. The problem may have been related to an intermittent electrical problem in the harness or in a connector. If an intermittent electrical problem is suspected, carefully inspect the connectors and wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Results: A short circuit diagnostic code -6 is active at this time.
Proceed to Test Step 3.
Result: An open circuit diagnostic code -5 is active at this time.
Proceed to Test Step 4.
   
Table 3
Troubleshooting Test Steps    Values    Results    
3. Disconnect the Connector for the Oil Renewal Solenoid in order to Create an Open Circuit
A. Disconnect the connector for the oil renewal solenoid.
B. Restore the electrical power to the engine ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Select diagnostic tests from Cat ET.
E. Select the "Override Parameters" screen on Cat ET.
F. Activate the override for the oil renewal solenoid.
G. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
H. Disable the override for the oil renewal solenoid.
    Open Circuit    
Results: A short circuit diagnostic code -6 was active before disconnecting the connector. An open circuit diagnostic code -5 became active after disconnecting the connector.
Repair: Temporarily connect a new oil renewal solenoid to the harness, but do not install the new solenoid. Verify that there are no active diagnostic codes for the oil renewal solenoid. If there are no active diagnostic codes for the solenoid, permanently install the new solenoid. Clear any logged diagnostic codes.
Results: A short circuit diagnostic code -6 remains active when the connector for the oil renewal solenoid is disconnected. There is a short circuit between the harness connector for the oil renewal solenoid and the ECM.
Proceed to Test Step 4.
   
Table 4
Troubleshooting Test Steps    Values    Results    
4. Create an Open at the ECM:
A. Disconnect the J1/P1 ECM connector.
B. Fabricate a jumper wire that is long enough to create a short between the ECM connector and engine ground. Crimp a connector socket to one end of the jumper wire.
C. Remove the wire from terminal location P1-20 (oil renewal solenoid) at the ECM connector. Install the jumper wire into this terminal location.
D. Connect the J1/P1 ECM connector.
E. Create an open at the ECM:
a. Restore the electrical power to the engine ECM.
Ensure that an open circuit c


Parts ball Suzuki:

09260-10003
 
09260-10003 Ball, Clutch Notch
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20M
09119-06047
Ball, Pivot
09119-06047 Ball, Pivot
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250,
83450-93720
 
83450-93720 Ball Joint
DT35ELT, DT35ELX, DT35ELZ, DT35EST, DT35ESX, DT35ESZ, DT35MLT, DT35MLX, DT35MLZ, DT35MST, DT35MSX, DT35MSZ, DT40, DT40ELT, DT40ELX, DT40ELZ, DT40EST, DT40ESX, DT40ESZ, DT40MLT, DT40MLX, DT40MLZ, DT40MSX, DT40MSZ, DT50, DT50ELB, DT50ELC, DT50ELN, DT50
09119-05010
Ball, pivot
09119-05010 Ball, pivot
30ELE, 30ESE, 30MLE, DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF25, DF250, DF250, DF250
09119-05011
 
09119-05011 BALL PIVOT
DT50, DT50, DT50M, DT50W, DT65, DT65
09119-06039
 
09119-06039 BALL PIVOT
DT50, DT50M, DT50W, DT65, DT65, DT85ELT, DT85TCLT, DT85TCLX, DT85TCLZ, DT85TELT
48844-87D00
 
48844-87D00 BALL HOLDER
DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT150TCXGP, DT150TCXGR, DT150T
Back to top