43754-94301-0ED Suzuki COVER, STEERING BRACKET


43754-94301-0ED COVER, STEERING BRACKET Suzuki DT25C, DT30C, DT30CRLJ, DT30CRSJ, DT30MCLJ, DT30MCSJ, DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C COVER
43754-94301-0ED COVER, STEERING BRACKET Suzuki
Rating:
13

Buy COVER, STEERING BRACKET 43754-94301-0ED Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 41
 

Suzuki entire parts catalog list:

DT25C 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000
DT30C 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998,1999,2000
DT30CRLJ 1988
DT30CRSJ 1988
DT30MCLJ 1988
DT30MCSJ 1988
DT35CRLH 1987
DT35CRLJ 1988
DT35CRLK 1989
DT35CRSH 1987
DT35CRSJ 1988
DT35CRSK 1989
DT35MCLH 1987
DT35MCLJ 1988
DT35MCLK 1989
DT35MCSH 1987
DT35MCSJ 1988
DT35MCSK 1989
DT35TCLH 1987
DT35TCLJ 1988
DT35TCLK 1989
DT40C 1986,1987,1988,1989,1990,1991,1992,1993,1994,1995,1996,1997,1998

Information:

Engine Design
Cylinder, Valve And Injection Pump LocationBore ... 137.2 mm (5.40 in)Stroke ... 152.4 mm (6.00 in)Number and Arrangement of Cylinders ... V-8Firing Order (Injection Sequence) ... 1,8,4,3,6,5,7,2Rotation of Crankshaft (when seen from flywheel end) ... counterclockwiseRotation of Fuel Pump Camshaft (when seen from pump drive end) ... counterclockwise Front end of engine is opposite to flywheel end.Left side and right side of engine are as seen from flywheel end.No. 1 cylinder is the front cylinder on the left side.No. 2 cylinder is the front cylinder on the right side.
Fuel System Schematic
(1) Fuel tank. (2) Tank shutoff valve. (3) Direct injection adapter. (4) Fuel manifolds. (5) Fuel injection pump housing. (6) Bleed orifice. (7) Fuel inlet line from secondary filters. (8) Fuel inlet line from primary filter. (9) Check valve. (10) Fuel transfer pump. (11) Secondary fuel filter. (12) Primary fuel filter. (13) Fuel priming pump. (14) Fuel transfer pump relief valve.Fuel System
There is one fuel injection pump and one fuel injection valve for each cylinder. The fuel injection pumps are located in the fuel injection pump housing. The fuel injection valves are located in direct injection adapter (3).When the engine is running, fuel is pulled from the fuel tank through the fuel supply line and primary fuel filter (12) by fuel transfer pump (10). The fuel is then pushed to secondary fuel filters (11), and into the fuel filter housing. A bleed orifice (6) in the fuel filter housing cover vents air in the system through a line back to fuel tank (1). Fuel from the fuel filter housing goes through inlet line (7) to fuel manifolds (4) in fuel injection pump housing (5). The fuel manifolds supply fuel to each fuel injection pump.Individual fuel injection lines carry fuel from the fuel injection pumps to each cylinder. One section of line connects between the fuel injection pump and an adapter on the valve cover base. Another section of line on the inside of the valve cover base connects between the adapter and the fuel injection valve in direct injection adapter (3).The fuel filters and priming pump are located in a compartment at the front of the fuel tank. The fuel transfer pump is mounted on a drive adapter on the fuel injection pump housing, and is driven by a shaft connected to the fuel injection pump camshaft. Fuel transfer pump relief valve (14) is located in the cover of the pump.Fuel priming pump (13) is used before the engine is started to put pressure in the fuel system and to vent air from the system. A check valve (9) located in the fuel transfer pump adapter housing will let fuel go around the fuel transfer pump when the priming pump is in use.There is no bleed orifice or valve installed on the fuel injection pump housing to vent air from this part of the fuel system. Air trapped in the fuel injection lines can be vented by loosening all of the fuel injection line nuts where they connect to the adapters in the valve cover base. Move the governor lever to the low idle position. Crank the engine with the starter motor until fuel without air comes from the fuel line connections. Tighten the fuel line nuts. This procedure is necessary because the fuel priming pump will not give enough pressure to push fuel through the reverse flow check valves in the fuel injection pumps of a direct injection system.
Location Of Fuel System Components
(4) Fuel manifolds. (5) Fuel injection pump housing. (7) Fuel inlet line from secondary filters. (8) Fuel inlet line from primary filter. (10) Fuel transfer pump.
Location Of Fuel System Components
(1) Fuel tank. (6) Bleed orifice in cover. (11) Secondary fuel filters. (12) Primary fuel filter. (13) Priming pump.An automatic timing advance unit is mounted on the front of the fuel injection pump camshaft. It is driven by the engine camshaft gear inside the front timing gear housing. The automatic timing advance unit gives easier starting and smooth low speed operation. It will also advance timing as engine speed increases to give correct engine operation efficiency.Fuel Injection Pump
The rotation of the lobes on the camshaft (12) cause lifters (9) and pump plungers (5) to move up and down. The stroke of each pump plunger is always the same. The force of springs (6) hold lifters (9) against the cams of the camshaft.The pump housing is a "V" shape (similiar to the engine cylinder block), with four pumps on each side.When the pump plunger is down, fuel from fuel manifold (1) goes through inlet passage (2) and fills the chamber above pump plunger (5). As the plunger moves up it closes the inlet passage.The pressure of the fuel in the chamber above the plunger increases until it is high enough to cause check valve (3) to open. Fuel under high pressure flows out of the check valve, through the fuel line to the injection valve, until the inlet passage opens into pressure relief passage (4) in the plunger. The pressure in the chamber decreases and check valve (3) closes.The longer inlet passage (2) is closed, the larger the amount of fuel which will be forced through check valve (3). The period for which the inlet passage is closed is controlled by pressure relief passage (4). The design of the passage makes it possible to change the inlet passage closed time by rotation of the plunger. When the governor moves fuel racks (8), they move gears (7) that are fastened to plungers (5). This causes a rotation of the plungers.
Cross Section Of The Fuel Injection Pump Housing
(1) Fuel manifold. (2) Inlet passage. (3) Check valve. (4) Pressure relief passage. (5) Pump plunger. (6) Spring. (7) Gear. (8) Fuel rack (left). (9) Lifter. (10) Link. (11) Lever. (12) Camshaft.The governor is connected to the left rack. The spring load on lever (11) removes the play between the racks and link (10). The fuel racks are connected by link (10). They move in opposite directions (when one rack moves


Parts cover Suzuki:

67267-95610
 
67267-95610 Cover, wire
DF15, DF15, DF15, DF150, DF150, DF150, DF150TX, DF150ZX, DF15S, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225T, DF225Z, DF25, DF25(R)S, DF250, DF250, DF250T, DF250Z, DF25Q, DF25Q(QR), DF25R, DF25R, DF25T, DF
11161-94400-0ED
 
11161-94400-0ED COVER, CYLINDER HEAD (GRAY)
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C
54221-94400-0ED
 
54221-94400-0ED COVER, LOWER MOUNT
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C
61403-94870-02M
31170-94520-OED
31170-94610-0ED
 
31170-94610-0ED COVER, UPPER
DT115, DT140, DT40C, DT55CRLJ, DT55CRLK, DT55CRLL, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT65CRLJ, DT65CRLK, DT65CRLL, DT65HTCLK, DT65HTCLL, DT65TCLJ, DT65
14141-94400-02M
 
14141-94400-02M Cover, Exhaust
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
13812-94401
 
13812-94401 Cover, Silencer
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK
Back to top