01421-08508 Stud Bolt Suzuki
DT5LD, DT5LT, DT5LX, DT5LZ, DT5SD, DT5ST, DT5SX, DT5SZ, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LT, DT8LX, DT8LZ, DT8SD, DT8SE, DT8SF, DT8ST, DT8SX, DT8SZ
Stud
Price: query
Rating:
Compatible models:
Suzuki entire parts catalog list:
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
- Handle » 01421-08508
Information:
The following background information is related to this procedure:Injector codes are 30 hexadecimal character codes that are supplied with each injector. The code is on a plate on the top of the injector and a card is also included in the packaging for the injector. The code is used by the ECM to balance the performance of the injectors.Refer to Troubleshooting, "Injector Code - Calibrate" for further information.
Illustration 1 g02131289
Typical code plate on an injector
Illustration 2 g02132293
Sequence for recording the injector code
During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
C. Check for active diagnostic codes or recently logged diagnostic codes.
Diagnostic codes
Result: No diagnostic codes are present.
Return the unit to service.
Result: One or more of the preceding diagnostic codes are active.
Make a note of any cylinder numbers with the active diagnostic code. Proceed to Test Step 2.
2. Check the Injector Code on any Suspect Cylinders
A. Connect the electronic service tool to the diagnostic connector. Refer to Troubleshooting, "Electronic Service Tools".
B. Turn the keyswitch to the ON position.
C. Select the following menu options on the electronic service tool to obtain the injector codes from the ECM:
"Service"
"Calibrations"
"Injector Trim Calibration"
D. Make a note of the injector codes for any suspect cylinders.
Diagnostic code
Result: The card that was supplied with the injector is available for the suspect cylinders.
Repair: Compare the injector code from the card with the injector code that was recorded from the electronic service tool for each suspect cylinder.
If the codes match, proceed to Test Step 3.
If the codes do not match, then use the electronic service tool to input the code from the card.
Result: The card with the injector code is not available.
Proceed to Test Step 3.
3. Manually Program the Injector Code
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
B. Make a note of the injector code that is on the injector in any suspect cylinders.
Note: Refer to Illustration 2 for the correct sequence for recording the injector code.
C. Compare the injector code from the injector with the injector code from the electronic service tool for each suspect cylinder.
Injector codes
Result: The code on the injector is the same as the code in the ECM. The injector is incorrect for the engine.
Repair: Replace the injector with the correct injector for the engine. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: The code on the injector is not the same as the code in the ECM.
Repair: Use the electronic service tool to input the correct injector code. Refer to Troubleshooting, "Injector Code - Calibrate" for the correct procedure.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
If the procedure did not correct the issue, contact the Dealer Solutions Network (DSN).
Illustration 1 g02131289
Typical code plate on an injector
Illustration 2 g02132293
Sequence for recording the injector code
During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
C. Check for active diagnostic codes or recently logged diagnostic codes.
Diagnostic codes
Result: No diagnostic codes are present.
Return the unit to service.
Result: One or more of the preceding diagnostic codes are active.
Make a note of any cylinder numbers with the active diagnostic code. Proceed to Test Step 2.
2. Check the Injector Code on any Suspect Cylinders
A. Connect the electronic service tool to the diagnostic connector. Refer to Troubleshooting, "Electronic Service Tools".
B. Turn the keyswitch to the ON position.
C. Select the following menu options on the electronic service tool to obtain the injector codes from the ECM:
"Service"
"Calibrations"
"Injector Trim Calibration"
D. Make a note of the injector codes for any suspect cylinders.
Diagnostic code
Result: The card that was supplied with the injector is available for the suspect cylinders.
Repair: Compare the injector code from the card with the injector code that was recorded from the electronic service tool for each suspect cylinder.
If the codes match, proceed to Test Step 3.
If the codes do not match, then use the electronic service tool to input the code from the card.
Result: The card with the injector code is not available.
Proceed to Test Step 3.
3. Manually Program the Injector Code
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
B. Make a note of the injector code that is on the injector in any suspect cylinders.
Note: Refer to Illustration 2 for the correct sequence for recording the injector code.
C. Compare the injector code from the injector with the injector code from the electronic service tool for each suspect cylinder.
Injector codes
Result: The code on the injector is the same as the code in the ECM. The injector is incorrect for the engine.
Repair: Replace the injector with the correct injector for the engine. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: The code on the injector is not the same as the code in the ECM.
Repair: Use the electronic service tool to input the correct injector code. Refer to Troubleshooting, "Injector Code - Calibrate" for the correct procedure.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
If the procedure did not correct the issue, contact the Dealer Solutions Network (DSN).
Parts stud Suzuki:
09108-06025
09108-06025 Stud Bolt, Housing
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ, DT4.5LB, DT4.5SB, DT4D, D
09108-05002
09108-05002 Stud Bolt, Lower Plate
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT4.5LB, DT4.5SB, DT4D, DT5LC, DT5LD, DT5LN, DT5LT, DT5LX, DT5LZ, DT5SC, DT5SD, DT5SN, DT5ST, DT5SX, DT5SZ, DT8LD, DT8LE, DT8LF, DT8L
09108-08036
09108-08036 Stud Bolt
DT14C, DT14D, DT14F, DT16LB, DT16LC, DT16LN, DT16LT, DT16LT, DT16LT, DT16SB, DT16SC, DT16SN, DT16ST, DT16ST, DT16ST, DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ, DT35ELT, DT35ELX, DT35ELZ
01411-06258
01411-06258 Stud Bolt
DT5LC, DT5LD, DT5LN, DT5LT, DT5LX, DT5LZ, DT5SC, DT5SD, DT5SN, DT5ST, DT5SX, DT5SZ
01421-06168
01421-06168 Stud Bolt
DT16LT, DT16LT, DT16LT, DT16ST, DT16ST, DT16ST, DT3.5LD, DT3.5LE, DT3.5LN, DT3.5LT, DT3.5LX, DT3.5LZ, DT3.5SD, DT3.5SE, DT3.5SN, DT3.5ST, DT3.5SX, DT3.5SZ, DT5LD, DT5LT, DT5LX, DT5LZ, DT5SD, DT5ST, DT5SX, DT5SZ, DT8LT, DT8LX, DT8LZ, DT8ST, DT8SX, DT8
01411-06558
01421-08608
01421-08608 Stud Bolt
DT5LD, DT5LT, DT5LX, DT5LZ, DT5SD, DT5ST, DT5SX, DT5SZ, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LT, DT8LX, DT8LZ, DT8SD, DT8SE, DT8SF, DT8ST, DT8SX, DT8SZ
01421-06128
01421-06128 Stud Bolt
DT5LD, DT5LT, DT5LX, DT5LZ, DT5SD, DT5ST, DT5SX, DT5SZ, DT6LE, DT6LF, DT6SE, DT6SF, DT8LD, DT8LE, DT8LF, DT8LT, DT8LX, DT8LZ, DT8SD, DT8SE, DT8SF, DT8ST, DT8SX, DT8SZ